FAN3268TMX Fairchild Semiconductor, FAN3268TMX Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
FAN3268TMX
Manufacturer Part Number
FAN3268TMX
Description
IC BRIDGE DVR P/N-CH 2A 8SOIC
Manufacturer
Fairchild Semiconductor
Specifications of FAN3268TMX
Configuration
Half Bridge
Input Type
Inverting and Non-Inverting
Delay Time
14ns
Current - Peak
3A
Number Of Configurations
1
Number Of Outputs
2
Voltage - Supply
4.5 V ~ 18 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Operating Temperature (max)
125C
Operating Temperature (min)
-40C
Pin Count
8
Mounting
Surface Mount
Package Type
SOIC N
Case Length
5(Max)mm
Case Height
1.5(Max)mm
Screening Level
Automotive
Product
Half-Bridge Drivers
Rise Time
22 ns
Fall Time
17 ns
Propagation Delay Time
25 ns
Supply Voltage (max)
18 V
Supply Voltage (min)
4.5 V
Supply Current
1.2 mA
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Bridge Type
Half Bridge
Minimum Operating Temperature
- 40 C
Output Current
2.4 A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
High Side Voltage - Max (bootstrap)
-
Lead Free Status / Rohs Status
Compliant
Other names
FAN3268TMXTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FAN3268TMX
Manufacturer:
FSC
Quantity:
1 000
© 2009 Fairchild Semiconductor Corporation
FAN3268 • Rev. 1.0.0
Applications Information
Input Thresholds
The FAN3268 driver has TTL input thresholds and
provides buffer and level translation functions from logic
inputs. The input thresholds meet industry-standard
TTL-logic thresholds, independent of the V
and there is a hysteresis voltage of approximately 0.4V.
These levels permit the inputs to be driven from a range
of input logic signal levels for which a voltage over 2V is
considered logic high. The driving signal for the TTL
inputs should have fast rising and falling edges with a
slew rate of 6V/µs or faster, so a rise time from 0 to
3.3V should be 550ns or less. With reduced slew rate,
circuit noise could cause the driver input voltage to
exceed the hysteresis voltage and retrigger the driver
input, causing erratic operation.
Static Supply Current
In the I
(see Figure 6) , the curve is produced with all inputs /
enables floating (OUT is low) and indicates the lowest
static I
states, additional current flows through the 100k Ω
resistors on the inputs and outputs shown in the block
diagram ( see Figure 3) . In these cases, the actual static
I
this additional current.
MillerDrive™ Gate Drive Technology
FAN3268 gate drivers incorporate the MillerDrive™
architecture shown in 0. For the output stage, a
combination of bipolar and MOS devices provide large
currents over a wide range of supply voltage and
temperature variations. The bipolar devices carry the
bulk of the current as OUT swings between one and two
thirds V
high or low rail.
The purpose of the MillerDrive™ architecture is to
speed up switching by providing high current during the
Miller plateau region when the gate-drain capacitance of
the MOSFET is being charged or discharged as part of
the turn-on / turn-off process.
For applications with zero voltage switching during the
MOSFET turn-on or turn-off interval, the driver supplies
high peak current for fast switching even though the
Miller plateau is not present. This situation often occurs
in synchronous rectifier applications because the body
diode is generally conducting before the MOSFET is
switched on.
The output pin slew rate is determined by V
and the load on the output. It is not user adjustable, but
a series resistor can be added if a slower rise or fall
time at the MOSFET gate is needed.
DD
current is the value obtained from the curves plus
DD
DD
DD
current for the tested configuration. For other
and the MOS devices pull the output to the
(static) typical performance characteristics
DD
DD
voltage,
voltage
11
Under-Voltage Lockout
Internal circuitry provides an under-voltage lockout
function that prevents the output switching devices from
operating if the V
operating level. When V
operational level, internal 100k Ω resistors bias the non-
inverting output low and the inverting output to V
keep the external MOSFETs off during startup intervals
when logic control signals may not be present. After the
part is active, the supply voltage must drop 0.2V before
the part shuts down. This hysteresis helps prevent
chatter when low V
the power switching.
V
To enable this IC to turn a device on quickly, a local
high-frequency bypass capacitor C
ESL should be connected between the VDD and GND
pins with minimal trace length. This capacitor is in
addition to bulk electrolytic capacitance of 10µF to 47µF
commonly found on driver and controller bias circuits.
A typical criterion for choosing the value of C
keep the ripple voltage on the V
is often achieved with a value ≥20 times the equivalent
load capacitance C
Ceramic capacitors of 0.1µF to 1µF or larger are
common choices, as are dielectrics, such as X5R and
X7R, with good temperature characteristics and high
pulse current capability.
If circuit noise affects normal operation, the value of
C
C
larger value, based on equivalent load capacitance, and
the other a smaller value, such as 1-10nF mounted
closest to the VDD and GND pins to carry the higher
frequency components of the current pulses. The
bypass capacitor must provide the pulsed current from
both of the driver channels and, if the drivers are
switching simultaneously, the combined peak current
sourced from the C
a single channel is switching.
BYP
BYP
DD
Figure 27. MillerDrive™ Output Architecture
Bypass Capacitor Guidelines
may be split into two capacitors. One should be a
may be increased to 50-100 times the C
BYP
DD
DD
EQV
supply voltages have noise from
would be twice as large as when
, defined here as Q
supply voltage is below the
DD
is rising, but below the 3.9V
DD
BYP
supply to ≤5%. This
with low ESR and
www.fairchildsemi.com
GATE
BYP
EQV
DD
/V
is to
DD
or
to
.