FS7M0680TU Fairchild Semiconductor, FS7M0680TU Datasheet
FS7M0680TU
Specifications of FS7M0680TU
Available stocks
Related parts for FS7M0680TU
FS7M0680TU Summary of contents
Page 1
... Vref Idelay Vsd Vcc Vovp ©2003 Fairchild Semiconductor Corporation Description The Fairchild Power Switch (FPS) product family is specially designed for an off line SMPS with minimal external compo- nents. The Fairchild Power Switch (FPS) consists of high volt- age power SenseFET and current mode PWM controller. The ...
Page 2
FS7M0680 Absolute Maximum Ratings Parameter (1) Maximum Drain Voltage Drain-Gate Voltage (R =1MΩ) GS Gate-Source (GND) Voltage (2) Drain Current Pulsed Single Pulsed Avalanche Energy (4) Avalanche Current Continuous Drain Current (T =25°C) C Continuous Drain Current (T =100°C) C ...
Page 3
Electrical Characteristics (SenseFET part) (Ta=25°C unless otherwise specified) Parameter Drain-Source Breakdown Voltage Zero Gate Voltage Drain Current Static Drain-Source On Resistance (note1) Forward Transconductance Input Capacitance Output Capacitance Reverse Transfer Capacitance Turn On Delay Time Rise Time Turn Off Delay ...
Page 4
FS7M0680 Electrical Characteristics (control part) (Ta=25°C unless otherwise specified) Parameter UVLO SECTION Start Threshold Voltage Stop Threshold Voltage OSCILLATOR SECTION Initial Frequency Frequency Change With Temperature Maximum Duty Cycle Voltage Stability FEEDBACK SECTION Feedback Source Current Shutdown Delay Current Shutdown ...
Page 5
General Application In general, the FPS consists of several functional sections: under voltage lockout circuit (UVLO), reference voltage, oscillator (OSC), pulse width modulation (PWM) block, pro- tection circuits and gate drive circuit. Start-Up The minimum current that FPS requires for ...
Page 6
FS7M0680 Vo Pulse by pulse current limit Figure 3 shows the pulse-width-modulation (PWM) block of the FPS. Since the FPS employs the peak current mode con- trol, the current through the power MOSFET is limited by the inverting input voltage ...
Page 7
Then, Vfb continues increasing and the preset maximum current flows through the primary side until the over load protection circuit is activated. Since maximum current is transferred to the secondary side, the secondary side voltage becomes much higher than the ...
Page 8
FS7M0680 3. Application Note using the FPS -Flyback Application (70W) HOT 5D-9 /NTC BD1 3.3 nF/630V 1 50uF /4 00V 700K /1W 2.2 nF 2.2nF 13mH Drain 5 FS7M0680R 0.1uF/275V AC GND ...
Page 9
Application (180W) Line NTC FUSE Inductor 472 /275V 0.47uF /275V 472 /275V 33kΩ /0.5W 33kΩ /0.5W Transformer Specification 2. Winding Specification PIN(S → F) No. 1 → P → 10, 11, 12 N+5V 13, 14 ...
Page 10
FS7M0680 Typical Performance Characteristics 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 -40 - Temperature [°C] Figure 1. Operating Supply Current vs. Temp. 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 -40 -20 0 ...
Page 11
Typical Performance Characteristics 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 -40 - Temperature [°C] Figure 7. Minimum Duty Cycle vs. Temp. 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 -40 - ...
Page 12
FS7M0680 Typical Performance Characteristics 1.4 1.3 1.2 1.1 1.0 0.9 0.8 -40 - Temperature [°C] Figure 13. Feedback Sink Current vs. Temp (Continued) 1.20 1.15 1.10 ...
Page 13
Package Dimensions TO-3P-5L FS7M0680 13 ...
Page 14
FS7M0680 Package Dimensions 14 (Continued) TO-3P-5L (Forming) ...
Page 15
... Ordering Information Product Number FS7M0680TU FS7M0680YDTU TO-3P-5L(Forming Non Forming Type YDTU : Forming type Package Rating TO-3P-5L 800V, 6A FS7M0680 Fosc 67kHz 15 ...
Page 16
... FS7M0680 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. ...