DSP56303 FREESCALE [Freescale Semiconductor, Inc], DSP56303 Datasheet - Page 174
![no-image](/images/no-image-200.jpg)
DSP56303
Manufacturer Part Number
DSP56303
Description
Manufacturer
FREESCALE [Freescale Semiconductor, Inc]
Datasheet
1.DSP56303.pdf
(292 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSP56303AG100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100B1
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
DSP56303GC100
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
DSP56303PV100
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
DSP56303PV100B
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
DSP56303PV100B
Manufacturer:
MAXIM
Quantity:
5 510
Company:
Part Number:
DSP56303VF100
Manufacturer:
MNDSPEED
Quantity:
2
Company:
Part Number:
DSP56303VF100
Manufacturer:
MOTOLOLA
Quantity:
513
Company:
Part Number:
DSP56303VF100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
DSP56303VF100
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
DSP56303VL100
Manufacturer:
FUJI
Quantity:
1 000
Serial Communication Interface (SCI)
8.4 SCI Initialization
The SCI is initialized as follows:
If interrupts are to be used, the signals must be selected, and global interrupts must be enabled
and unmasked before the SCI can operate. The order does not matter; any one of these three
requirements for interrupts can enable the SCI, but the interrupts should be unmasked last (that is,
I[1–0] bits in the Status Register (SR) should be changed last). Synchronous applications usually
require exact frequencies, so the crystal frequency must be chosen carefully. An alternative to
selecting the system clock to accommodate the SCI requirements is to provide an external clock
to the SCI. When the SCI is configured in Synchronous mode, internal clock, and all the SCI pins
are simultaneously enabled, an extra pulse of one DSP clock length is provided on the
There are two workarounds for this issue:
Following is an example of one way to initialize the SCI:
Note:
Note:
8-6
1.
2.
3.
1.
2.
3.
4.
5.
Enable an SCI pin other than
In the next instruction, enable the remaining SCI pins, including the
Ensure that the SCI is in its individual reset state (PCRE = $0). Use a hardware
signal or software RESET instruction.
Program the SCI control registers.
Configure at least one SCI signal as an SCI signal.
Ensure that the SCI is in its individual reset state (PCRE = $0).
Configure the control registers (SCR, SCCR) according to the operating mode, but do
not enable transmitter (TE = 0) or receiver (RE = 0).
Enable the SCI by setting the PCRE bits according to which signals are used during
operation.
If transmit interrupt is not used, write data to the transmitter.
Enable transmitters (TE = 1) and receiver (RE = 1) according to use.
It is now possible to set the interrupts enable bits that are used during the operation. No
interrupt occurs yet.
If transmitter interrupt enable is set, an interrupt is issued and the interrupt handler
should write data into the transmitter. The DMA channel services the SCI transmit
request if it is programmed to service the SCI transmitter.
DSP56303 User’s Manual, Rev. 2
SCLK
.
SCLK
Freescale Semiconductor
pin.
SCLK
RESET
pin.