S29PL032J SPANSION [SPANSION], S29PL032J Datasheet - Page 66
![no-image](/images/no-image-200.jpg)
S29PL032J
Manufacturer Part Number
S29PL032J
Description
CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S29PL032J.pdf
(106 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S29PL032J-DC-B
Manufacturer:
SPANSION
Quantity:
20 000
Company:
Part Number:
S29PL032J55BF112
Manufacturer:
SPANSION
Quantity:
1 000
Part Number:
S29PL032J55BFI020A
Manufacturer:
FUJITSU/富士通
Quantity:
20 000
Company:
Part Number:
S29PL032J55BFI120
Manufacturer:
SPANSION
Quantity:
1 200
Company:
Part Number:
S29PL032J55BFI120
Manufacturer:
SPANSION
Quantity:
1 000
Company:
Part Number:
S29PL032J55BFI120A
Manufacturer:
SPANSION
Quantity:
2 000
Company:
Part Number:
S29PL032J55BFI120E
Manufacturer:
CYPRESS
Quantity:
1 200
Part Number:
S29PL032J60BFI12
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29PL032J60BFI120
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29PL032J60BFI123
Manufacturer:
SPANSION
Quantity:
20 000
Command Definitions
64
Reading Array Data
Reset Command
Writing specific address and data commands or sequences into the command
register initiates device operations.
sequences. Writing incorrect address and data values or writing them in the
improper sequence may place the device in an unknown state. A reset com-
mand is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE# (CE1# / CE2# in
PL129J), whichever happens later. All data is latched on the rising edge of WE#
or CE# (CE1# / CE2# in PL129J), whichever happens first. Refer to the
acteristic" section section for timing diagrams.
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data. Each bank is ready to read array data
after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the corresponding bank
enters the erase-suspend-read mode, after which the system can read data from
any non-erase-suspended sector within the same bank. The system can read
array data using the standard read timing, except that if it reads at an address
within erase-suspended sectors, the device outputs status data. After completing
a programming operation in the Erase Suspend mode, the system may once
again read array data with the same exception. See the
Resume
The system must issue the reset command to return a bank to the read (or
erase-suspend-read) mode if DQ5 goes high during an active program or erase
operation, or if the bank is in the autoselect mode. See the next section,
Command" section, for more information.
See also
erations" section section for more information. The
table provides the read parameters, and Figure 12 shows the timing diagram.
Writing the reset command resets the banks to the read or erase-suspend-read
mode. Address bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the bank to which the sys-
tem was writing to the read mode. Once erasure begins, however, the device
ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins. This resets the bank to which
the system was writing to the read mode. If the program command sequence is
written to a bank that is in the Erase Suspend mode, writing the reset command
returns that bank to the erase-suspend-read mode. Once programming begins,
however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command must be
written to return to the read mode. If a bank entered the autoselect mode while
in the Erase Suspend mode, writing the reset command returns that bank to the
erase-suspend-read mode.
Commands" section section for more information.
"Requirements for Reading Array
S29PL127J/S29PL129J/S29PL064J/S29PL032J
P R E L I M I N A R Y
Table 21
Data" section in the
defines the valid register command
"AC
Characteristic" section
"Erase Suspend/Erase
"Device Bus Op-
"AC Char-
"Reset
31107A62 April 7, 2005