S29PL032J SPANSION [SPANSION], S29PL032J Datasheet - Page 59
![no-image](/images/no-image-200.jpg)
S29PL032J
Manufacturer Part Number
S29PL032J
Description
CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S29PL032J.pdf
(106 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S29PL032J-DC-B
Manufacturer:
SPANSION
Quantity:
20 000
Company:
Part Number:
S29PL032J55BF112
Manufacturer:
SPANSION
Quantity:
1 000
Part Number:
S29PL032J55BFI020A
Manufacturer:
FUJITSU/富士通
Quantity:
20 000
Company:
Part Number:
S29PL032J55BFI120
Manufacturer:
SPANSION
Quantity:
1 200
Company:
Part Number:
S29PL032J55BFI120
Manufacturer:
SPANSION
Quantity:
1 000
Company:
Part Number:
S29PL032J55BFI120A
Manufacturer:
SPANSION
Quantity:
2 000
Company:
Part Number:
S29PL032J55BFI120E
Manufacturer:
CYPRESS
Quantity:
1 200
Part Number:
S29PL032J60BFI12
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29PL032J60BFI120
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29PL032J60BFI123
Manufacturer:
SPANSION
Quantity:
20 000
April 7, 2005 31107A62
Temporary Sector Unprotect
SecSi™ (Secured Silicon) Sector Flash Memory Region
This feature allows temporary unprotection of previously protected sectors to
change data in-system. The Sector Unprotect mode is activated by setting the
RESET# pin to
grammed or erased by selecting the sector addresses. Once V
the RESET# pin, all the previously protected sectors are protected again. 2 shows
the algorithm, and 21 shows the timing diagrams, for this feature. While PPB lock
is set, the device cannot enter the Temporary Sector Unprotection Mode.
Notes:
1. All protected sectors unprotected (If WP#/ACC = V
2. All previously protected sectors are protected once again
The SecSi (Secured Silicon) Sector feature provides a Flash memory region that
enables permanent part identification through an Electronic Serial Number (ESN)
The 128-word SecSi sector is divided into 64 factory-lockable words that can be
programmed and locked by the customer. The SecSi sector is located at ad-
dresses 000000h-00007Fh in both Persistent Protection mode and Password
Protection mode. Indicator bits DQ6 and DQ7 are used to indicate the fac-
tory-locked and customer locked status of the part.
The system accesses the SecSi Sector through a command sequence (see the
"Enter SecSi™ Sector/Exit SecSi Sector Command
system has written the Enter SecSi Sector command sequence, it may read the
SecSi Sector by using the addresses normally occupied by the boot sectors. This
mode of operation continues until the system issues the Exit SecSi Sector com-
mand sequence, or until power is removed from the device. On power-up, or
following a hardware reset, the device reverts to sending commands to the nor-
mal address space. Note that the ACC function and unlock bypass modes are not
available when the SecSi Sector is enabled.
Factory-Locked Area (64 words)
The factory-locked area of the SecSi Sector (000000h-00003Fh) is locked when
the part is shipped, whether or not the area was programmed at the factory. The
sectors will remain protected).
Figure 2. Temporary Sector Unprotect Operation
V
ID
P R E L I M I N A R Y
. During this mode, formerly protected sectors can be pro-
S29PL127J/S29PL129J/S29PL064J/S29PL032J
Unprotect Completed
Program Operations
Temporary Sector
Perform Erase or
RESET# = V
RESET# = V
(Note 1)
(Note 2)
START
ID
IH
Sequence" section). After the
IL
, upper two and lower two
ID
is removed from
57