r6781-12 Conexant Systems, Inc., r6781-12 Datasheet - Page 77
r6781-12
Manufacturer Part Number
r6781-12
Description
Embedded Modem Family
Manufacturer
Conexant Systems, Inc.
Datasheet
1.R6781-12.pdf
(104 pages)
- Current page: 77 of 104
- Download datasheet (730Kb)
EmbeddedModem Family
6.5.2 Ring Detection
Table 6-5. Fax Class 1 Calling Sequence (1 of 2)
D224ATLVDSC
(1) AT+FCLASS=1
(3) ATDT6163
(10) AT+FRH=3
(14) AT+FRH=3
(19) AT+FTH=3
(22) <TSI>
(26) <DCS>
DTE Commands
(Host)
—
—
—
—
—
—
—
—
—
(2) OK
(4) Dials
(6) CONNECT
(9) <NSF>, OK
(11) CONNECT
(13) <CIS>, OK
(15) CONNECT
(17) <DIS>, OK
(20) Send HDLC flags
(21) CONNECT
(23) Send TSI frame
(25) CONNECT
(27) Send DCS frame
(29) Detect last frame bit
DCE Responses
(Modem)
Ring detection is based on a digital input to the modem. External circuitry not
part of the modem is required to convert the analog 40 to 150 V
a digital single-bit data stream representation. Valid ring frequencies of 15.3 to 68
Hz are detected. Detection is achieved by counting valid high to low ring signal
transitions. Valid transitions consist of a high state of 2 to 34 ms followed by a low
state of 2 to 42 ms. Ring signals that have transition counts less than the nominal
value are discarded.
cadence of the ring ON time (valid transitions occurring) and ring OFF time (no
valid transitions). Ring OFF times must be greater than 0.5 seconds. Ring ON
times must be greater than 125 ms at 20 Hz (100 ms at 68 Hz).
at 8 second intervals. The modem will answer the ring after N valid ON/OFF ring
cycles. N is programmable via the S0 register. Upon detecting N rings, the
modem verifies that the current ring state has been in the OFF state for 0.5
seconds before seizing the line.
sequence.
—
—
—
In addition to valid high to low transitions, ring detection depends on the
Ring detection is integrated over 8 seconds. All counters and timers are reset
Table 6-5
lists the Fax Class 1 calling sequence;
(5) Answers
(7) Send HDLC flags
(8) Send NSF frame
(12) Send CSI frame
(16) Send DIS frame
(18) Drop carrier
(21) Receive flags
(24) Receive TSI
(28) Received DCS
Conexant
PHASE A
PHASE B
Remote Fax
—
—
—
—
—
—
—
—
Set to Class 1
+FRH=3 implied by Dialing
Last frame bit = 1
Last frame bit = 0
Last frame bit = 1
Table 6-6
Notes
—
—
—
—
—
—
—
—
—
—
—
lists the answering
RMS
6.5 Call Progress
ring signal to
6-13
Related parts for r6781-12
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Bluetooth RF Transceiver
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Bluetooth RF Transceiver
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
ATM transmitter/receiver with UTOPIA interface
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Service SAR controller
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
CN8223EPFATM Transmitter/Receiver with UTOPIA Interface
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Embedded modem family
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Fully integrated T1/E1 framer and line interface
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Flicker-free video encoder
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Home Networking Physical Layer Device with Integrated Analog Front End Circuitry Data Sheet (Preliminary) CX82100-41Home Network Processor (HNP)
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Flicker-free video encoder
Manufacturer:
Conexant Systems, Inc.
Datasheet: