am79c850 Advanced Micro Devices, am79c850 Datasheet - Page 29
am79c850
Manufacturer Part Number
am79c850
Description
Supernet-r 3
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C850.pdf
(97 pages)
- Current page: 29 of 97
- Download datasheet (342Kb)
(if transmitting), releases the token, and no further
transmissions can occur until the pin is deasserted.
During the time that the TRANSMIT INHIBIT function is
enabled the network timers and state machines
operate normally.
As a result of the change to the FLXI pin, which of the
two functions is selected depends upon the state of FLXI
bits, as follows:
Single Frame Receive Mode
The Single Frame Receive Mode function has been
removed from the SUPERNET 3. All associated status,
modes and commands are deleted and replaced with
reserved. This causes the following changes:
1. Status Register 2 Upper:
Upon reset, the FLXI1:0 bits would read all zeros.
FLXI
The ‘Receive Frame’ (SRCVFRM) bit 10 and
‘Receive Frame Counter Overflow’ (SRFRCTOV) bit
9 are now reserved and return a value of zero when
read.
Pin
0
1
0
1
0
1
0
1
FLXI1
0
0
0
0
1
1
1
1
FLXI0
0
0
1
1
0
0
1
1
Function Implemented
Normal Operation
Normal Operation
Normal Operation
FLUSH received frame
Normal Operation
INHIBIT transmission
Reserved
Reserved
P R E L I M I N A R Y
SUPERNET 3
2. Command Register 2:
3. Mode Register 1:
Receive Queue Operation
SUPERNET 3 provides a new feature where the user
can configure the buffer memory for incoming valid
frame into two separate receive queues. The type of
frames that each queue would receive is selected in a
separate register, the Frame Selection Register
(FRSELREG). To enable two receive queues operation,
MENDRCV bit in Mode Register 3 (MDREG3) needs to
be set. If this bit is cleared, which is the case at the time
of reset, then SUPERNET 3 behaves like F+ (i.e only
one receive queue is supported, and SUPERNET 3
defaults to Receive Queue 1). If MDREG3 bit 11,
MENDRCV and both RECVX3:0 in Frame Selection
Register (FRSELREG) is programmed to be “0000”
then the SUPERNET 3 would behave like FORMAC+
and the second queue is ignored. However, if one of the
RECVX3:0 bits in FRSELREG are programmed to be
“0000” then the corresponding queue would receive all
frames except the frame type selected for the other
queue. Only the second receive queue (i.e. RECV2) can
be programmed to be “0000”. Programming the RECV1
bits in the Frame Selection Register (FRSELREG) with
“0000” and RECV2 bits with a non-zero selection, will
result in no data being written in the RECV1 queue. Only
the frame type selected by RECV2 bits will be received
in the second queue.
The ‘Enable Receive Single Frame’ command
(0x40) is no longer a valid command. This is now
reserved.
The ‘Single-Frame Receive Mode’ bit [15] is no
longer valid. It is now a reserved bit and shall return a
value of zero when read.
AMD
29
Related parts for am79c850
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Advanced Micro Devices [8 Megabit (512 K x 16-Bit) CMOS 3.0 Volt-only Burst Mode Flash Memory]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
M41000001YAdvanced Micro Devices [32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory and 4 Mbit (512 K x 8-Bit/256 K x 16-Bit) Static RAM]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Advanced Burst Error Processor
Manufacturer:
Advanced Micro Devices
Part Number:
Description:
Serial interface adapter (SIA)
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Universal interrupt controller
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
256 kilobit CMOS EPROM
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
2048 x 8 static RAM, 100ns
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
AM2966PCOctal Dynamic Memory Drivers with Three-State Outputs
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
TTL programmable array logic, 7ns
Manufacturer:
Advanced Micro Devices
Datasheet: