agl030 Actel Corporation, agl030 Datasheet - Page 132

• Manufacturer Part Number: agl030
• Description: Igloo Low-power Flash Fpgas With Flash*freeze Technology
• Manufacturer: Actel Corporation

IGLOO DC and Switching Characteristics
Part Number and Revision Date
List of Changes
2 -1 1 8
Previous Version
Advance v0.2
Advance v0.1
(January 2008)
Part Number 51700095-002-2
Revised July 2008
The following table lists critical changes that were made in the current version of the chapter.
As a result of the Libero IDE v8.4 release, Actel now offers a wide range of
core voltage support. The document was updated to change 1.2 V / 1.5 V to
1.2 V to 1.5 V.
Tables have been updated to reflect default values in the software. The
default I/O capacitance is 5 pF. Tables have been updated to include the
LVCMOS 1.2 V I/O set.
DDR Tables have two additional data points added to reflect both edges for
Input DDR setup and hold time.
The power data table has been updated to match SmartPower data rather
then simulation values.
AGL015 global clock delays have been added.
Table 2-1 · Absolute Maximum Ratings
VMV parameters in one row. The word "output" from the parameter
description for V
Table 2-2 · Recommended Operating Conditions
references to tables notes 4, 6, 7, and 8. VMV was added to the V
row, and table note 9 was added.
In
Temperature1, the maximum operating junction temperature was changed
from 110° to 100°.
VMV was removed from
table title was modified to remove "as measured on quiet I/Os." Table note 2
was revised to remove "estimated SSO density over cycles." Table note 3 was
revised to remove "refers only to overshoot/undershoot limits for
simultaneous switching I/Os.
The
Figure 2-2 · V2 Devices – I/O State as a Function of V
is new.
EQ 2-2
the end result changed.
The table notes for
IGLOO Flash*Freeze
Characteristics, IGLOO Sleep Mode (VCC = 0
Supply Current (I
V)*
were removed from the statement about I
Table 2-9 · Quiescent Supply Current (I
(VCC = 0
Note 2 of
Mode1
and P
Table 2-3 · Flash Programming Limits – Retention, Storage, and Operating
were updated to remove VMV and include P
"PLL Behavior at Brownout Condition" section
DC7
was updated. The temperature was changed to 100°C, and therefore
was updated to include V
.
V)*.
Table 2-11 · Quiescent Supply Current (I
CCI
DD
Changes in Current Version (Advance v0.3)
and VMV, and table note 3 was added.
) Characteristics, IGLOO Shutdown Mode (VCC, VCCI = 0
Table 2-8 · Quiescent Supply Current (I
Mode*,
Table 2-4 · Overshoot and Undershoot Limits
A d v a n c e v 0. 3
"
Table 2-9 · Quiescent Supply Current (I
CCPLL
DD
. Note 4 was updated to include P
was updated to combine the V
) Characteristics, IGLOO Sleep Mode
V)*, and
DD
DC6
DD
4
is new.
CCI
), No IGLOO Flash*Freeze
and P
in the table note for
was updated to add
and V
Table 2-10 · Quiescent
DC7
DD
CC
) Characteristics,
. V
Voltage Levels
CCI
CCI
parameter
and V
CCI
1. The
JTAG
and
DD
DC6
)
Page
N/A
N/A
2-1
2-2
2-2
2-3
2-4
2-5
2-6
2-7
2-8