w83l517g Winbond Electronics Corp America, w83l517g Datasheet - Page 21
w83l517g
Manufacturer Part Number
w83l517g
Description
Winbond Lpc I/o For Notebook W83l517d/ W83l517d-f
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W83L517G.pdf
(133 pages)
- Current page: 21 of 133
- Download datasheet (864Kb)
5. LPC (LOW PIN COUNT) INTERFACE
LPC interface is to replace ISA interface serving as a bus interface between host (chip-set) and
peripheral (Winbond I/O). Data transfer on the LPC bus are serialized over a 4 bit bus. The general
characteristics of the interface implemented in Winbond LPC I/O are:
•
•
•
•
•
•
•
Comparing to its ISA counterpart, LPC implementation saves up to 40 pin counts free for integrating
more devices on a single chip.
The transition from ISA to LPC is transparent in terms of software which means no BIOS or device
driver update is needed except chip-specific configuration.
6. FDC FUNCTIONAL DESCRIPTION
6.1
The floppy disk controller of the W8369L517D integrates all of the logic required for floppy disk
control.
compatible values. The FIFO provides better system performance in multi-master systems. The
digital data separator supports up to 2 M bits/sec data rate.
The FDC includes the following blocks: AT interface, Precompensation, Data Rate Selection, Digital
Data Separator, FIFO, and FDC Core.
6.1.1
The interface consists of the standard asynchronous signals: RD# , WR#, A0-A3, IRQ, DMA control,
and a data bus. The address lines select between the configuration registers, the FIFO and
control/status registers. This interface can be switched between PC/AT, Model 30, or PS/2 normal
modes. The PS/2 register sets are a superset of the registers found in a PC/AT.
6.1.2
The FIFO is 16 bytes in size and has programmable threshold values. All command parameter
information and disk data transfers go through the FIFO. Data transfers are governed by the RQM and
DIO bits in the Main Status Register.
The FIFO defaults to disabled mode after any form of reset. This maintains PC/AT hardware
compatibility. The default values can be changed through the CONFIGURE command. The advantage
of the FIFO is that it allows the system a larger DMA latency without causing disk errors. The following
tables give several examples of the delays with a FIFO. The data are based upon the following
formula:
One control line, namely LFRAME#, which is used by the host to start or stop transfers. No
peripherals drive this signal.
The LAD[3:0] bus, which communicates information serially. The information conveyed are cycle
type, cycle direction, chip selection, address, data, and wait states.
MR (master reset) of Winbond ISA I/O is replaced with a active low reset signal, namely
LRESET#, in Winbond LPC I/O.
An additional 33 MHz PCI clock is needed in Winbond LPC I/O for synchronization.
DMA requests are issued through LDRQ#.
Interrupt requests are issued through SERIRQ.
Power management events are issued through PME#.
W83L517D FDC
AT interface
FIFO (Data)
The FDC implements a PC/AT or PS/2 solution.
- 21 -
W83L517D/W83L517D-F
All programmable options default to
Publication Release Date: May 23, 2005
Revision 1.0
Related parts for w83l517g
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 845 Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Via P4/kt Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel 915/925 Chipsets
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Pa-risc Embedded Controller
Manufacturer:
Winbond Electronics Corp America
Datasheet: