w83l517g Winbond Electronics Corp America, w83l517g Datasheet - Page 104
![no-image](/images/no-image-200.jpg)
w83l517g
Manufacturer Part Number
w83l517g
Description
Winbond Lpc I/o For Notebook W83l517d/ W83l517d-f
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W83L517G.pdf
(133 pages)
- Current page: 104 of 133
- Download datasheet (864Kb)
9.4
In this mode, the W83627HF changes the printer interface pins to FDC input/output pins, allowing the
user to install a second floppy disk drive (FDD B) through the DB-25 printer connector. The pin
assignments for the FDC input/output pins are shown in Table 6-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOB# and DSB# will be forced to inactive state.
(2) Pins DSKCHG# , RDATA# , WP# , TRAK0# , INDEX# will be logically ORed with pins PD4-PD0 to
serve as input signals to the FDC.
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for
FDD open drain/collector output.
(4) If the parallel port is set to EXTFDD mode after the system has booted DOS or another operating
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
9.5
In this mode, the W83627HF changes the printer interface pins to FDC input/output pins, allowing the
user to install two external floppy disk drives through the DB-25 printer connector to replace internal
floppy disk drives A and B. The pin assignments for the FDC input/output pins are shown in Table6-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOA# , DSA# , MOB# , and DSB# will be forced to inactive state.
(2) Pins DSKCHG# , RDATA# , WP# , TRAK0# , and INDEX# will be logically ORed with pins PD4-PD0 to serve as
input signals to the FDC.
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for FDD open
drain/collector output.
(4) If the parallel port is set to EXT2FDD mode after the system has booted DOS or another operating system, a
warm reset is needed to enable the system to recognize the extension floppy drive.
10. GENERAL PURPOSE I/O
W83L517D provides 38 input/output ports that can be individually configured to perform a simple
basic I/O function or a pre-defined alternate function. Those 38 GP I/O ports are divided into five
groups, each group contains 6,8,8,8,8 ports from group 1 to group 5. The first group is configured
through control registers in logical device 7, the second group in logical device 8,the third ,the
fourth,and the fifth group in logical device 9. Users can configure each individual port to be an input or
output port by programming respective bit in selection register (CRF0: 0 = output, 1 = input). Invert
port value by setting inversion register (CRF2: 0 = non-inverse, 1 = inverse). Port value is read/written
through data register (CRF1). Table 7.1 and 7.2 gives more details on GPIO's assignment. In
addition, GPIO1 is designed to be functional even in power loss condition (VCC or VSB is off). Figure
7.1 shows the GP I/O port's structure. Right after Power-on reset, those ports default to perform basic
input function except ports in GPIO1 which maintains its previous settings until a battery loss
condition.
Extension FDD Mode (EXTFDD)
Extension 2FDD Mode (EXT2FDD)
- 104 -
W83L517D/W83L517D-F
Related parts for w83l517g
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![w83l784r](/images/no-image3.png)
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83627thg](/images/no-image3.png)
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83601r](/images/no-image3.png)
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83977atf](/images/no-image3.png)
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83194br-sd](/images/no-image3.png)
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83194br-603](/images/no-image3.png)
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83194br-619](/images/no-image3.png)
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83194br-b](/images/no-image3.png)
Part Number:
Description:
Winbond Clock Generator For Intel P4 845 Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83195bg-341](/images/no-image3.png)
Part Number:
Description:
Winbond Clock Generator For Via P4/kt Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83195bg-101](/images/no-image3.png)
Part Number:
Description:
Winbond Clock Generator For Intel 915/925 Chipsets
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83l784r](/images/no-image3.png)
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83627thg](/images/no-image3.png)
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83601r](/images/no-image3.png)
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![w83977atf](/images/no-image3.png)
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![W90210F](/images/no-image3.png)
Part Number:
Description:
Pa-risc Embedded Controller
Manufacturer:
Winbond Electronics Corp America
Datasheet: