MD3331-D32-V3Q18 M-Systems Inc., MD3331-D32-V3Q18 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
MD3331-D32-V3Q18
Manufacturer Part Number
MD3331-D32-V3Q18
Description
Mobile Diskonchip Plus 128Mbits 1.8V I/o
Manufacturer
M-Systems Inc.
Datasheet
1.MD3331-D32-V3Q18.pdf
(66 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MD3331-D32-V3Q18-X
Manufacturer:
SIPEX
Quantity:
7 500
2.2.3 Signal Description
The ball designations are listed in the signal descriptions, presented in logic groups, in Table 1.
11
A[12:11]
A[10:8]
A[7:4]
A[3:0]
BHE#
CE#
D[7:0]
D[15:8]
OE#
WE#
ID[1:0]
IF_CFG
LOCK#
BUSY#
IRQ#
RSTIN#
VCCQ
Signal
J8, G7, K7, H6,
H8, K8, H7, J7,
D2, E2, F2, G2
C3, D3, E3, F3
H5, K4, G4, J3
K5, J4, H4, K3
F7, E7, C7
Ball No.
D8, C8
G9, F8
H2
H3
C6
D5
E4
F4
E8
E5
F9
J6
ST, R8 Byte High Enable, active low. When low, data transaction on
IN, R8 Data bus, high byte. Not used and may be left floating when
ST, R Chip Enable, active low.
Input
Type
OD
ST
ST
ST
ST
ST
ST
ST
Table 1: Standard Interface Signal Descriptions
IN
-
Address bus.
D[15:8] is enabled. Not used and may be left floating when
IF_CFG is set to 0 (8-bit mode).
Data bus, low byte.
IF_CFG is set to 0 (8-bit mode).
Output Enable, active low
Write Enable, active low
Identification.
For Mobile DiskOnChip 16MB, up to four chips can be cascaded
in the same memory window, according to the following
assignment:
Chip 1 = ID1, ID0 = VSS, VSS (0,0); required for single chip
Chip 2 = ID1, ID0 = VSS, VCC (0,1)
Chip 3 = ID1, ID0 = VCC, VSS (1,0)
Chip 4 = ID1, ID0 = VCC, VCC (1,1)
For Mobile DiskOnChip 32MB, up to two chips can be cascaded in
the same memory window, according to the following assignment:
Chip 1 : ID1=VSS, ID0 = VSS ;required for single chip
Chip 2 : ID1=VSS, ID0 = VCC
Interface Configuration, 1 for 16-bit interface mode, 0 for 8-bit
interface mode.
Lock, active low. When active, provides full hardware data
protection of selected partitions.
Busy, active low, open drain. Indicates that DiskOnChip is
initializing and should not be accessed. A 10 K
required even if the ball is not used.
Interrupt Request. Requires a 10 K
Reset, active low.
I/O power supply. Sets the logic ‘1’ voltage level range of I/O
balls/pins. VCCQ may be either 2.5V to 3.6V or 1.65V to 2.0V.
Requires a 10 nF and 0.1 µF capacitor.
Data Sheet, Rev. 1.7
System Interface
Configuration
Control
Power
Description
Ω
Mobile DiskOnChip Plus 16/32MByte 1.8V I/O
pull-up resistor.
Ω
pull-up resistor is
95-SR-000-10-8L
Input
Input
Input
Input/
Output
Input/
Output
Input
Input
Input
Input
Input
Output
Output
Input
Supply
Signal
Type