LPC2292 Philips Semiconductors (Acquired by NXP), LPC2292 Datasheet - Page 10

• Manufacturer Part Number: LPC2292
• Description: 16/32-bit Arm Microcontrollers; 256 KB Isp/iap Flash With CAN, 10-bit ADC And External Memory Interfacebased on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support, Together With 256 Kilobytes (kB) of Embedded High Speed
• Manufacturer: Philips Semiconductors (Acquired by NXP)

Philips Semiconductors
Table 3:
9397 750 12748
Preliminary data
Symbol
P3.20
P3.21
P3.22
P3.23
P3.24
P3.25
P3.26
P3.27
P3.28
P3.29
P3.30
P3.31
TD1
RESET
XTAL1
XTAL2
V
V
V
V
V
V
V
SS
SSA
SSA_PLL
18
18A
3
3A
Pin description
Pin
45
44
41
40
36
35
30
29
28
27
97
96
22
135
142
141
3, 9, 26, 38,
54, 67, 79,
93, 103, 107,
111, 128
139
138
37, 110
143
2, 31, 39, 51,
57, 77, 94,
104, 112, 119
14
…continued
Type
O
I
I
O
O
O
I
I
I
I
I
I
I
O
O
O
I/O
O
O
O
O
O
O
I
I
O
Description
A20 — External memory address line 20.
A21 — External memory address line 21.
A22 — External memory address line 22.
A23 — External memory address line 23.
XCLK — Clock output.
CS3 — Low-active Chip Select 3 signal.
(Bank 3 addresses range 8300 0000 - 83FF FFFF)
CS2 — Low-active Chip Select 2signal.
(Bank 2 addresses range 8200 0000 - 82FF FFFF)
CS1 — Low-active Chip Select 1 signal.
(Bank 1 addresses range 8100 0000 - 81FF FFFF)
WE — Low-active Write enable signal.
BLS3 — Low-active Byte Lane Select signal (Bank 3).
AIN7 — A/D converter, input 7. This analog input is always connected to its
pin.
BLS2 — Low-active Byte Lane Select signal (Bank 2).
AIN6 — A/D converter, input 6. This analog input is always connected to its
pin.
BLS1 — Low-active Byte Lane Select signal (Bank 1).
BLS0 — Low-active Byte Lane Select signal (Bank 0).
TD1: CAN1 transmitter output.
External Reset input: A LOW on this pin resets the device, causing I/O ports
and peripherals to take on their default states, and processor execution to
begin at address 0. TTL with hysteresis, 5 V tolerant.
Input to the oscillator circuit and internal clock generator circuits.
Output from the oscillator amplifier.
Ground: 0 V reference.
Analog Ground: 0 V reference. This should nominally be the same voltage
as V
PLL Analog Ground: 0 V reference. This should nominally be the same
voltage as V
1.8 V Core Power Supply: This is the power supply voltage for internal
circuitry.
Analog 1.8 V Core Power Supply: This is the power supply voltage for
internal circuitry. This should be nominally the same voltage as V
be isolated to minimize noise and error.
3.3 V Pad Power Supply: This is the power supply voltage for the I/O ports.
Analog 3.3 V Pad Power Supply: This should be nominally the same voltage
as V
Rev. 01 — 05 February 2004
16/32-bit ARM microcontrollers with external memory interface
SS
3
but should be isolated to minimize noise and error.
, but should be isolated to minimize noise and error.
SS
, but should be isolated to minimize noise and error.
LPC2292/LPC2294
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
18
but should
10 of 40