S1D10605 Epson Electronics America, Inc., S1D10605 Datasheet - Page 525

no-image

S1D10605

Manufacturer Part Number
S1D10605
Description
S1d15000 Series Lcd Driver With Ram
Manufacturer
Epson Electronics America, Inc.
Datasheet
<A setting example: When setting Ta = 25C and V
to 9V on an S1D15A06
ture gradient = –0.1% C>
ues (D4, D3, D2, D1, D0) = (1, 0, 0, 0, 0) are selected
from the electronic volume. Thus, using expression C-
1, you can select V
ing manner:
If you select 5 uA for the current to be conducted across
V
and R3 can be derived as shown below:
* When using the built-in V
* V
* Since V
Voltage Follower Circuit
The V
V
V
follower, and provide to LCD driver circuit.
LCD bias ratio can be selected by LCD bias set command
which is 1/6 bias or 1/8 bias for S1D15A06 series.
On-chip Power Supply Turn Off Sequence
Before turning the built-in power supply off, to discharge
the remaining electric charge of LCD panel and power
supply PIN etc., it is recommended to turn on the power
Table 18
Rev. 1.0a
Sequence
0
4
3
ment circuit and the voltage follower circuit must be activated, as a minimum requirement, by the power control set
command. When the booster is circuit is turned off, necessary voltage must be supplied from V
these resistors are used.
wiring distance shorter or using shielded wire.
= 15 and V
9V ={1+(R3+R2) / R1} • (1–15/200) • 1.2
R3 + R2=7.11 • R1
voltages by on-chip resistor circuit. And the V
and V
and V
Table 17
R
Step1
Step2
[ ]: Commands selected from the electronic volume.
End
pin is enabled only when the built-in V
Variable range
Variable step
0
voltage is divided to generate the V
4
SS
R
voltages are impedance-converted by voltage
pin has a higher input impedance, appropriate noise protection measures must provided including cutting the
when V
REG
V
(command and state)
0
Display all points on
= 1.2V when intermediate resistor val-
Built-in power OFF
0
0
= 9V when R2 = 0 in the follow-
Display OFF
= 7V, sum of resistance of R1, R2
Contents
*****
6.39[80H]
0
voltage adjusting resistors or the electronic volume function, both of the voltage adjust-
Min.
model with Tempera-
(Expression C-2)
1
, V
0
D7
to
voltage adjusting resistors are not used. V
1
1
0
2
, V
1
3
0
, V
and
D6
= 5
0
0
0
2
7.0[90H]
EPSON
,
Typ.
38.1
D5
1
1
1
Command address
From expressions C-2 and C-3, R1 = 1.4M /
8.11=173k .
And, you can select V = 5V when R2 = R2 through the
following computation:
R2 = 137@ and R3 = 1.09 M are derived from expres-
sions C-2, C-3 and C-4.
Table 15 lists the commands used, and Table 17 shows
V
able from the electronic volume.
save mode employing the following command sequence.
You can also turn the built-in power supply off by ini-
tializing it using RES pin or the reset command. Here,
of S1D15A06D00B
only used, LOW level signal entering RES pin discharges
V
and V
with external power supply being used, discharge the
electric charge by short-circuiting the external power
supply to V
being saved. (V
functions are not in the IC)
D4
5V = ={1+R3/(R1+R2) } • (1–15/200) • 1.2
R3/(R1 + R2) = 3.5
0
OUT
R1 + R2 + R3 = 1.4M
0
0
0
voltage variable voltage range and variable steps avail-
, thereby introducing shorting across V
0
–V
D3
to
1
0
1
SS
. Of S1D15A06D01B
SS
when the power supply is off or power is
D2
OUT
1
1
0
7.57[9FH]
Max.
*
and V
D1
with built-in power supply being
1
0
0
R
pin must be made open when
0
D0
electric charge discharging
0
1
0
S1D15A06 Series
(Expression C-4).
(Expression C-3).
*
Power save
c o m m a n d
(composite
command)
[mV]
OUT
Unit
/S1D15A06D02B
[V]
.
OUT
12–21
–V
DD2
*

Related parts for S1D10605