S1D10605 Epson Electronics America, Inc., S1D10605 Datasheet - Page 207

• Manufacturer Part Number: S1D10605
• Description: S1d15000 Series Lcd Driver With Ram
• Manufacturer: Epson Electronics America, Inc.

Notes: *1. Although the wide range of operating voltage is guaranteed, a spike voltage change during access to the
*14, 15, 16 Indicates the current consumed by the separate IC. The current consumption due to the LCD panel
S1D15600/601/602 Series
- Dynamic current consumption (I), if the built-in power supply is used.
7–12
I
DD
( A)
(1)
*10. “tr” (reset time) indicates the period between the time when the RES signal rises and when the internal
*11. Specifies the minimum pulse width of RES” signal. The LOW pulse greater than “
*12. If the voltage is amplified three times by the built-in power circuit, the primary power V
*13. The V
*14. Applied if an external clock is used and if not accessed by the MPU.
*15. Applied if the built-in oscillation circuit is used and if not accessed by the MPU.
*16. Applied if the built-in oscillation circuit and the built-in power circuit are used (T1 = T2 = Low) and if
200
150
100
*2. The operating voltage range of the V
*3. Pins A0, D0 to D7, RD (E), WR (R/W), CS1, CS2, FR, SYNC, M/S, C86, SI, P/S, T1 and T2.
*4. Pins CL, SCL, and RES
*5. Pins D0 to D7, FR, SYNC, CL0, and DY0
*6. Pins A0, RD (E), WR (R/W), CS1, CS2, CL, M/S, RES, C86, SI, SCL, P/S, T1, and T2.
*7. Applied if pins D0 to D7, FR, and SYNC are high impedance.
*8. The resistance when the 0.1-volt voltage is applied between the “On” output terminal and each power
*9. The relationship between the oscillation frequency, frame and Rf value (see Figure 10).
50
0
MPU is not guaranteed.
The operating voltage range is applied if an external power supply is used.
terminal (V1, V2, V3 or V4). It must be within the operating voltage (2).
R ON = 0.1 V/ I
( I is the current that flows when 0.1 VDC is applied during power-on.)
circuit has been reset. Therefore, the S1D1560
for reset.
within the input voltage range.
circuit.
capacity and wiring capacity is not included.
The current consumption is shown if the checker is used, the display is turned on, the output status of
Case 6 is selected, and the S1D15600D00B
duty, and the S1D15602D00B
not accessed by the MPU. Measuring conditions: C1 = 4.7 F, C2 = 0.47 F, Ra + Rb = 2 M
This includes the current that flows through the voltage regulator resistor (Ra + Rb = 2 M ). If the
built-in power circuit is used, the current consumption is equal to the current of V
1
5
voltage can be adjusted within the voltage follower operating range by the voltage regulator
2
3
V
DD
4
5
*
is set to 1/16 duty.
6
(V)
SS
and V
7
EPSON
*
5
is set to 1/64 duty, the S1D15601D00B
*
systems (see Figure 11).
is usually operable after “tr” time.
Conditions:
Remarks:
The built-in power supply is on and
T1 = T2 = Low.
S1D15600 V
S1D15601 V
S1D15602 V
Internal oscillation:
S1D15600 R
S1D15601 R
S1D15602 R
*16
times amplified
times amplified
times amplified
5
5
5
f
f
f
SS
= 1 M
= 1 M
= 1 M
– V
– V
– V
t
RW
power.
*
” must be entered
DD
DD
DD
is set to 1/32
SS
= –12.5 V; 3
= –8.0 V; 3
= –6.0 V; 2
must be used
Rev. 4.6