STE10-100A STMicroelectronics, STE10-100A Datasheet - Page 9
STE10-100A
Manufacturer Part Number
STE10-100A
Description
Pci 10/100 Ethernet Controller With Integrated Phy
Manufacturer
STMicroelectronics
Datasheet
1.STE10-100A.pdf
(82 pages)
- Current page: 9 of 82
- Download datasheet (795Kb)
STE10/100A
Table 1.
Boot ROM/EEPROM interface
Pin no.
56~59
61~66
80~86
67~71
17
28
42
18
20
21
22
23
24
25
26
87
72
73
74
76
77
78
79
3
4
BrD5/EDO
Pin description (continued)
BrD7/ECK
DEVSEL#
BrA10~15
LED M2 -
BrD6/EDI
FRAME#
C-BEB3
C-BEB2
C-BEB1
C-BEB0
BrA0~3
BrA4~9
BrD0~4
PERR#
SERR#
TRDY#
STOP#
BrWE#
BrA16/
Fd/Col
BrCS#
BrOE#
IDSEL
IRDY#
Name
EECS
PAR
Type
O/D
O/O
O/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O/I
O
O
O
O
O
I
Bus command and byte enable
Initialization device select. This signal is asserted when the
host issues configuration cycles to the STE10/100A.
Asserted by PCI bus master during bus tenure
Master device is ready to begin data transaction
Target device is ready to begin data transaction
Device select. Indicates that a PCI target device address has
been decoded
PCI target device request to the PCI master to stop the
current transaction
Data parity error detected, driven by the device receiving
data
Address parity error
Parity. Even parity computed for AD[31:0] and C/BE[3:0];
master drives PAR for address and write data phase, target
drives PAR for read data phase.
ROM data bus
Provides up to 128Kbit EPROM or flash-ROM application
space.
This pin can be programmed as mode 2 LED display for full
duplex or collision status. It will be driven (LED on)
continually when a full duplex configuration is detected, or it
will be driven at a 20 Hz blinking frequency when a collision
status is detected in the half duplex configuration.
BootROM data bus (0~7)
EDO: Data output of serial EEPROM, data input to
STE10/100A
EDI: Data input to serial EEPROM, data output from
STE10/100A
ECK: Clock input to serial EEPROM, sourced by
STE10/100A
Chip select of serial EEPROM
BootROM chip select
BootROM read output enable for flash ROM application
BootROM write enable for flash ROM application.
Description
Pin description
9/82
Related parts for STE10-100A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools Eval Board for STE10
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10/100A - PCI 10/100 ETHERNET CONTROLLER WITH PHY DATASHEET
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A - PCI 10-100 ETHERNET CONTROLLER WITH PHY DATASHEET
Manufacturer:
STMicroelectronics
Part Number:
Description:
IC CTRLR PCI ETHERNET 128-PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
PCI10-100 ETHERNET CONTROLLER WITH INTEGRATED PHY (5V)
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A - PCI 10-100 ETHERNET CONTROLLER WITH PHY APPNOTE
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A EEPROM ACCESS AND PROGRAMMING
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet: