FAN2106 Fairchild Semiconductor, FAN2106 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
FAN2106
Manufacturer Part Number
FAN2106
Description
This part is covered in Fairchild's href="http://www
Manufacturer
Fairchild Semiconductor
Datasheet
1.FAN2106.pdf
(15 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
FAN2106MPX
Manufacturer:
FAIRCHILD/仙童
Quantity:
20 000
© 2009 Fairchild Semiconductor Corporation
FAN2106 • Rev. 1.1.1
Circuit Description
PWM Generation
Refer to Figure 2 for the PWM control mechanism.
FAN2106 uses the summing-mode method of control to
generate the PWM pulses. An amplified current-sense
signal is summed with an internally generated ramp and
the combined signal is compared with the output of the
error amplifier to generate the pulsewidth to drive the
high-side MOSFET. Sensed current from the previous
cycle is used to modulate the output of the summing
block. The output of the summing block is also
compared against a voltage threshold set by the R
resistor to limit the inductor current on a cycle-by-cycle
basis. The R
for the internal ramp and provides input voltage feed-
forward function. The controller facilitates external
compensation for enhanced flexibility.
Initialization
Once V
the IC checks for a shorted FB pin before releasing the
internal soft-start ramp (SS).
If the parallel combination of R1 and R
internal SS ramp is not released and the regulator does
not start.
Enable
FAN2106 has an internal pull-up to the ENABLE (EN)
pin so that the IC is enabled once V
UVLO threshold. Connecting a small capacitor across
EN and AGND delays the rate of voltage rise on the EN
pin. The EN pin also serves for the restart whenever a
fault occurs (refer to the Auto-Restart section). If the
regulator is enabled externally, the external EN signal
should go HIGH only after V
applications where such sequencing is required,
FAN2106 can be enabled (after the V
external control, as shown in Figure 21.
Soft-Start
Once internal SS ramp has charged to 0.8V (T0.8), the
output voltage is in regulation. Until SS ramp reaches
1.0V (T1.0), the fault latch is inhibited.
To avoid skipping the soft-start cycle, it is necessary to
apply V
sequence for powering up would be VINVCCEN.
Figure 21. Enabling with External Control
IN
CC
before V
exceeds the UVLO threshold and EN is HIGH,
RAMP
CC
resistor helps set the charging current
reaches its UVLO threshold. Normal
CC
is established. For
CC
BIAS
CC
comes up) with
is 1K, the
exceeds the
LIM
10
Soft-start time is a function of switching frequency.
Cycling V
and resets the IC. In applications where external EN
signal is used, V
the EN signal comes up to prevent skipping the soft-
start function.
Startup on Pre-Bias
The regulator does not allow the low-side MOSFET to
operate in full synchronous rectification mode until
internal SS ramp reaches 95% of V
helps the regulator start on a pre-biased output and
ensures that the pre-biased outputs are not discharged
during soft-start.
Protections
The converter output is monitored and protected against
extreme overload, short-circuit, over-voltage, under-
voltage, and over-temperature conditions.
Under-Voltage Shutdown
If the voltage on the FB pin remains below the under-
voltage threshold for 16 consecutive clock cycles, the
fault latch is set and the converter shuts down. This
protection is not active until the internal SS ramp
reaches 1.0V during soft-start.
Over-Voltage Protection
If voltage on the FB pin exceeds 115% of V
consecutive clock cycles, the fault latch is set and
shutdown occurs.
A shorted high-side MOSFET condition is detected
when SW voltage exceeds ~0.7V while the low-side
EN
FB
SS
Figure 22. Soft-Start Timing Diagram
CC
or the EN pin discharges the internal SS
IN
and V
1.35V
3200 CLKs
4000 CLKs
2400 CLKs
CC
1.0V
0.8V
should be established before
T0.8
T1.0
REF
(~0.76V). This
Fault
Latch
Enable
0.8V
www.fairchildsemi.com
REF
for two