FAN5665 Fairchild Semiconductor, FAN5665 Datasheet - Page 12

• Manufacturer Part Number: FAN5665
• Description: The FAN5665 is a 5V switched capacitor step-up DC/DC converter with an input voltage range from 2
• Manufacturer: Fairchild Semiconductor

© 2007 Fairchild Semiconductor Corporation
FAN5665 • Rev. 1.0.1
Applications Information
The high switching frequency of 1.2MHz allows the use
of small capacitors, but the material of the capacitor
affects the input and output ripple, so the low-ESR
capacitors are desirable. Another parameter affected by
ESR is the efficiency. For proper operation, two ceramic
bucket capacitors, along with one ceramic input
capacitor and one ceramic output capacitor, are
recommended (as shown in Figure 1).
Input Capacitor Selection
In general, the ripple on the input power rail also affects
the output ripple. The lower the ESR of the input
capacitor, the lower the input and output ripple. The
input capacitor may need to be adjusted, both in its
value and in its physical placement on the PCB,
depending upon the characteristics of the voltage
source proving the input power. In general, a 1 to 2µF
ceramic capacitor placed close to the FAN5665
suffices. X5R and X7R capacitors provide adequate
performance over -40ºC to +85ºC. The following table
represents typical recommended input capacitors.
Output Capacitor Selection
In
recommended for low ESR. The value of the output bulk
capacitance in relation to the switching frequency of the
converter also determines the overall output voltage
ripple. A higher value of output capacitance reduces the
voltage droop during load transients. Typically, the
output capacitor can be 5 to 50 times larger than the
bucket capacitor(s), depending on the desired output
ripple tolerance. Both X5R- and X7R-rated capacitors
provide adequate performance over a -40ºC to +85ºC
temperature range. The following table contains typical
recommended output capacitors.
Capacitor
2.2µF, 10%,
6.3V, X5R,
0603
Capacitor
2.2µF, 20%,
6.3V, X5R,
0402
Capacitor
2.2µF, 10%,
6.3V, X5R,
0603
Capacitor
2.2µF, 20%,
6.3V, X5R,
0402
Description
Description
general,
multilayer
GRM188R60J225KE19D
GRM155R60J225ME15D
GRM188R60J225KE19D
GRM155R60J225ME15D
Part Number
Part Number
ceramic
capacitors
Murata
Murata
Murata
Murata
Vendor
Vendor
are
12
Bucket Capacitor Selection
The bucket (flying) capacitor is usually the smallest
capacitor in a charge pump circuit, but its ESR can play
a significant role in determining the output voltage
tolerance. Only ceramic capacitors are recommended in
this position. The flying capacitance is determined by
the switching frequency. At 1.2MHz, 0.22µF flying
capacitors are suitable for most applications, but can be
increased to improve the output tolerance. Depending
on the material of the multilayer ceramic capacitor, a
substantial amount of capacitance may be lost over a
wide temperature range. At least X5R and X7R
capacitors are recommended for their relatively stable
temperature characteristics. Z5U- or Y5V-type capacitors
are not recommended. The following table shows a
typical recommended bucket capacitor.
Increasing Output Current Capability
Two parallel FAN5665s increase the output current. In
such a configuration, the VIN, VOUT, GND, and EN
pins of each IC should be connected together, but the
respective C1 and C2 pins must be kept separate.
Separate local input and output bypassing / decoupling
may be required to reduce output noise and ripple.
Capacitor
0.22µF, 10%,
6.3V, X5R,
0402
Description
EN
+5V
C
2.2µF
OUT
Figure 40. Two FAN5665s in Parallel
C
2.2µF
0.22µF
0.22µF
OUT
C1
C1
GRM155R60J224KE01D
EN
VOUT
C1+
C1-
EN
VOUT
C1+
C1-
Part Number
GND
GND
C2+
C2+
VIN
VIN
C2-
C2-
0.22µF
C2
0.22µF
C2
2.2µF
2.2µF
C
C
IN
IN
www.fairchildsemi.com
Murata
Vendor
2.9 to5.5V
V
BAT