FMS6501MSA28X Fairchild Semiconductor, FMS6501MSA28X Datasheet - Page 10

• Manufacturer Part Number: FMS6501MSA28X
• Description: IC VIDEO SW MATRIX 12X9 28SSOP
• Manufacturer: Fairchild Semiconductor
• Type: Video Switch, 12-Input 9-Outputr

Specifications of FMS6501MSA28X

• Applications: Set-Top Boxes
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: FMS6501MSA28XTR; FMS6501MSA28X_NL; FMS6501MSA28X_NLTR; FMS6501MSA28X_NLTR

© 2004 Fairchild Semiconductor Corporation
FMS6501 Rev. 1.0.4
Applications Information
Input Clamp / Bias Circuitry
The FMS6501 accommodates AC- or DC-coupled inputs.
Internal clamping and bias circuitry are provided to sup-
port AC-coupled inputs. These are selectable through
the CLMP bits via the I
For DC-coupled inputs, the device should be pro-
grammed to use the 'bias' input configuration. In this con-
figuration, the input is internally biased to 625mV through
a 100kΩ resistor. Distortion is optimized with the output
levels set between 250mV above ground and 500mV
below the power supply. These constraints, along with
the desired channel gain, need to be considered when
configuring the input signal levels for input DC coupling.
With AC-coupled inputs, the FMS6501 uses a simple
clamp rather than a full DC-restore circuit. For video sig-
nals with and without sync (Y,CV,R,G,B), the lowest volt-
age at the output pins is clamped to approximately
300mV above ground when the 6dB gain setting is
selected.
If symmetric AC-coupled input signals are used
(chroma,Pb,Pr,Cb,Cr), the bias circuit described above
can be used to center them within the input common
range. The average DC value at the output is approxi-
mately 1.27V with a 6dB gain setting. This value
changes depending upon the selected gain setting.
Figure 8 shows the clamp mode input circuit and the
internally controlled voltage at the input pin for AC-cou-
pled inputs.
Video source must
be AC-coupled
Gain Setting
6dB
7dB
8dB
9dB
Figure 8. Clamp Mode Input Circuit
Clamp Voltage
2
Lowest voltage
C compatible interface.
300mV
330mV
370mV
420mV
set to 125mV
75
0.1µF
Bias Voltage
FMS6501
Clamp
Input
1.27V
1.43V
1.60V
1.80V
10
Figure 9 shows the bias mode input circuit and internally
controlled voltage at the input pin for AC-coupled inputs.
Output Configuration
The FMS6501 outputs may be either AC or DC coupled.
Resistive output loads can be as low as 75Ω, represent-
ing a dual, doubly terminated video load. High imped-
ance, capacitive loads up to 20pF can also be driven
without loss of signal integrity. For standard 75Ω video
loads, a 75Ω matching resistor should be placed in
series to allow for a doubly terminated load. DC-coupled
outputs should be connected as shown in Figure 10.
If multiple low-impedance loads are DC coupled,
increased power and thermal issues need to be
addressed. In this case, the use of a multilayer board
with a large ground plane to help dissipate heat is rec-
ommended. If a two-layer board is used under these
conditions, an extended ground plane directly under the
device is recommended. This plane should extend at
least 0.5 inches beyond the device. PC board layout
issues are covered in the Layout Considerations section.
AC-coupled loads should be configured as in Figure 11:
Video source must
be AC-coupled
Figure 10. DC-Coupled Load Connection
Figure 11. AC-Coupled Load Connection
Figure 9. Bias Mode Input Circuit
FMS6501
Amplifier
Output
FMS6501
Amplifier
Output
Lowest voltage
set to 625mV
75
0.1µF
75
75
220µF
75
FMS6501
75
www.fairchildsemi.com
Input
Bias