P89LPC932A1 NXP Semiconductors, P89LPC932A1 Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
P89LPC932A1
Manufacturer Part Number
P89LPC932A1
Description
The P89LPC932A1 is a single-chip microcontroller, available in low cost packages, basedon a high performance processor architecture that executes instructions in two to fourclocks, six times the rate of standard 80C51 devices
Manufacturer
NXP Semiconductors
Datasheet
1.P89LPC932A1.pdf
(64 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P89LPC932A1
Manufacturer:
PHAEDRUS
Quantity:
185
Part Number:
P89LPC932A1FA
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P89LPC932A1FA,112
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P89LPC932A1FA,129
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P89LPC932A1FAЈ¬112
Manufacturer:
NXP
Quantity:
9 947
Company:
Part Number:
P89LPC932A1FDH
Manufacturer:
VISHAY
Quantity:
120 000
Part Number:
P89LPC932A1FDH
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P89LPC932A1FDHЈ¬512
Manufacturer:
NXP
Quantity:
836
Company:
Part Number:
P89LPC932A1FHN
Manufacturer:
IR
Quantity:
4 510
NXP Semiconductors
P89LPC932A1_3
Product data sheet
7.13.1.4 Push-pull output configuration
7.13.2 Port 0 analog functions
7.13.3 Additional port features
7.14.1 Brownout detection
7.14 Power monitoring functions
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a Schmitt
trigger input that also has a glitch suppression circuit.
The P89LPC932A1 incorporates two Analog Comparators. In order to give the best
analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-only (high-impedance)
mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
After power-up, all pins are in Input-only mode. Please note that this is different from
the LPC76x series of devices.
Every output on the P89LPC932A1 has been designed to sink typical LED drive current.
However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
The P89LPC932A1 incorporates power monitoring functions designed to prevent
incorrect operation during initial power-up and power loss or reduction during operation.
This is accomplished with two hardware functions: Power-on detect and brownout detect.
The brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a brownout detection to cause a processor reset,
however it may alternatively be configured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If brownout detection is the brownout condition occurs when V
trip voltage, V
above V
below 2.7 V, BOE should be left in the unprogrammed state so that the device can operate
at 2.4 V, otherwise continuous brownout reset may prevent the device from operating.
•
•
After power-up, all I/O pins except P1.5, may be configured by software.
Pin P1.5 is input only. Pins P1.2 and P1.3 and are configurable for either input-only or
open-drain.
bo
. If the P89LPC932A1 device is to operate with a power supply that can be
bo
(see
Table 8 “Static
Rev. 03 — 12 March 2007
8-bit microcontroller with accelerated two-clock 80C51 core
Table 8 “Static characteristics”
characteristics”), and is negated when V
for detailed specifications.
P89LPC932A1
DD
falls below the brownout
© NXP B.V. 2007. All rights reserved.
DD
rises
23 of 64