SAM9G20 Atmel Corporation, SAM9G20 Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM9G20
Manufacturer Part Number
SAM9G20
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9261.pdf
(248 pages)
2.SAM9261.pdf
(1274 pages)
3.SAM9261.pdf
(43 pages)
4.SAM9G20.pdf
(42 pages)
5.SAM9G20.pdf
(832 pages)
Specifications of SAM9G20
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
7
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
95
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No/Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
10.4.4
10.4.5
6384DS–ATARM–13-Jan-10
Serial Synchronous Controller
Timer Counter
The USART contains features allowing management of the Modem Signals DTR, DSR, DCD
and RI. In the AT91SAM9G20, only the USART0 implements these signals, named DTR0,
DSR0, DCD0 and RI0.
The USART1 and USART2 do not implement all the modem signals. Only RTS and CTS (RTS1
and CTS1, RTS2 and CTS2, respectively) are implemented in these USARTs for other features.
Thus, programming the USART1, USART2 or the USART3 in Modem Mode may lead to unpre-
dictable results. In these USARTs, the commands relating to the Modem Mode have no effect
and the status bits relating the status of the modem signals are never activated.
• RS485 with driver control signal
• ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards
• IrDA modulation and demodulation
• Test Modes
• Provides serial synchronous communication links used in audio and telecom applications
• Contains an independent receiver and transmitter and a common clock divider
• Offers a configurable frame sync and data length
• Receiver and transmitter can be programmed to start automatically or on detection of
• Receiver and transmitter include a data signal, a clock signal and a frame synchronization
• Two blocks of three 16-bit Timer Counter channels
• Each channel can be individually programmed to perform a wide range of functions including:
• Each channel is user-configurable and contains:
(with CODECs in Master or Slave Modes, I
different event on the frame sync signal
signal
– By 8 or by-16 over-sampling receiver frequency
– Hardware handshaking RTS-CTS
– Optional modem signal management DTR-DSR-DCD-RI
– Receiver time-out and transmitter timeguard
– Optional Multi-drop Mode with address generation and detection
– Optional Manchester Encoding
– NACK handling, error counter with repetition and iteration limit
– Communication at up to 115.2 Kbps
– Remote Loopback, Local Loopback, Automatic Echo
– Frequency Measurement
– Event Counting
– Interval Measurement
– Pulse Generation
– Delay Timing
– Pulse Width Modulation
– Up/down Capabilities
2
S, TDM Buses, Magnetic Card Reader, etc.)
AT91SAM9G20 Summary
35