ATxmega128B3 Atmel Corporation, ATxmega128B3 Datasheet - Page 379

• Manufacturer Part Number: ATxmega128B3
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B3

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

28.6
28.6.1
28.6.2
8291A–AVR–10/11
Register Description - PDI Instruction and Addressing Registers
Instruction Register
Pointer Register
Figure 28-14. PDI instruction set summary.
The PDI instruction and addressing registers are internal registers utilized for instruction decod-
ing and PDIBUS addressing. None of these registers are accessible as registers in a register
space.
When an instruction is successfully shifted into the physical layer shift register, it is copied into
the instruction register. The instruction is retained until another instruction is loaded. The reason
for this is that the REPEAT command may force the same instruction to be run repeatedly,
requiring command decoding to be performed several times on the same instruction.
The pointer register is used to store an address value that specifies locations within the PDIBUS
address space. During direct data access, the pointer register is updated by the specified num-
ber of address bytes given as operand bytes to an instruction. During indirect data access,
REPEAT
LDCS
STCS
KEY
LDS
STS
LD
ST
0
0
0
0
1
1
1
1
Cmd
Cmd
0
1
0
1
0
1
0
1
0
0
1
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
Size A
Ptr
CS Address
0
0
0
Size A/B
Size B
Size B
0
Atmel AVR XMEGA B
Cmd
0
0
0
0
1
1
1
1
Size A - Address size (direct access)
0
0
1
1 1
Ptr - Pointer access (indirect access)
0
0
1
1 1
Size B - Data size
0
0
1
1 1
CS Address (CS - Control/Status reg.)
0
0
0
0
1
0
0
1
1 1
0 0
0
1
1 1
0
1
0
0
1
0
0
1
0
0 0
0 0
0 1
0 1
1 1
0
1
0
1
0
Byte
Word (2 Bytes)
3 Bytes
Long (4 Bytes)
*(ptr)
*(ptr++)
ptr
ptr++ - Reserved
Byte
Word (2 Bytes)
3 Bytes
Long (4 Bytes)
LDS
LD
STS
ST
LDCS (LDS Control/Status)
REPEAT
STCS (STS Control/Status)
KEY
0
1
0
1
1
Register 0
Register 1
Register 2
Reserved
Reserved
......
379