ATtiny88 Atmel Corporation, ATtiny88 Datasheet - Page 141
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny88
Manufacturer Part Number
ATtiny88
Description
Manufacturer
Atmel Corporation
Specifications of ATtiny88
Flash (kbytes)
8 Kbytes
Pin Count
32
Max. Operating Frequency
12 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
28
Ext Interrupts
28
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
64
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
2
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATtiny88-12AU
Manufacturer:
ATMEL
Quantity:
2 165
Company:
Part Number:
ATtiny88-15AZ
Manufacturer:
Atmel
Quantity:
7 370
Company:
Part Number:
ATtiny88-15MZ
Manufacturer:
ATMEL
Quantity:
3 500
Part Number:
ATtiny88-15MZ
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny88-AU
Manufacturer:
ATMEL
Quantity:
5 000
Company:
Part Number:
ATtiny88-AU
Manufacturer:
ATMEL
Quantity:
3 000
Part Number:
ATtiny88-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny88-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny88-MUR
Manufacturer:
AT
Quantity:
20 000
15.8.1
8008H–AVR–04/11
Master Transmitter Mode
The following sections describe each of these modes. Possible status codes are described
along with figures detailing data transmission in each of the modes. These figures contain the
following abbreviations:
In
numbers in the circles show the status code held in TWSR, with the prescaler bits masked to
zero. At these points, actions must be taken by the application to continue or complete the TWI
transfer. The TWI transfer is suspended until the TWINT Flag is cleared by software.
When the TWINT Flag is set, the status code in TWSR is used to determine the appropriate soft-
ware action. For each status code, the required software action and details of the following serial
transfer are given in
these tables.
In the Master Transmitter mode, a number of data bytes are transmitted to a Slave Receiver
(see
The format of the following address packet determines whether Master Transmitter or Master
Receiver mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is trans-
mitted, MR mode is entered. All the status codes mentioned in this section assume that the
prescaler bits are zero or are masked to zero.
Figure 15-11. Data Transfer in Master Transmitter Mode
SDA
SCL
Figure 15-12
S: START condition
Rs: REPEATED START condition
R: Read bit (high level at SDA)
W: Write bit (low level at SDA)
A: Acknowledge bit (low level at SDA)
A: Not acknowledge bit (high level at SDA)
Data: 8-bit data byte
P: STOP condition
SLA: Slave Address
Figure
15-11). In order to enter a Master mode, a START condition must be transmitted.
TRANSMITTER
Device 1
to
MASTER
Figure
Table 15-2
15-18, circles are used to indicate that the TWINT Flag is set. The
Device 2
RECEIVER
SLAVE
to
Table
15-5. Note that the prescaler bits are masked to zero in
Device 3
........
Device n
V
CC
ATtiny48/88
R1
R2
141