ATtiny88 Atmel Corporation, ATtiny88 Datasheet - Page 139
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny88
Manufacturer Part Number
ATtiny88
Description
Manufacturer
Atmel Corporation
Specifications of ATtiny88
Flash (kbytes)
8 Kbytes
Pin Count
32
Max. Operating Frequency
12 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
28
Ext Interrupts
28
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
64
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
2
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATtiny88-12AU
Manufacturer:
ATMEL
Quantity:
2 165
Company:
Part Number:
ATtiny88-15AZ
Manufacturer:
Atmel
Quantity:
7 370
Company:
Part Number:
ATtiny88-15MZ
Manufacturer:
ATMEL
Quantity:
3 500
Part Number:
ATtiny88-15MZ
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny88-AU
Manufacturer:
ATMEL
Quantity:
5 000
Company:
Part Number:
ATtiny88-AU
Manufacturer:
ATMEL
Quantity:
3 000
Part Number:
ATtiny88-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny88-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny88-MUR
Manufacturer:
AT
Quantity:
20 000
8008H–AVR–04/11
1
2
Assembly Code Example
ldi
(1<<TWINT)|(1<<TWSTA)|
out
wait1:
in
sbrs r16,TWINT
rjmp wait1
r16,
(1<<TWEN)
TWCR, r16
r16,TWCR
Even though this example is simple, it shows the principles involved in all TWI transmissions.
These can be summarized as follows:
In the following an assembly and C implementation of the example is given. Note that the code
below assumes that several definitions have been made, for example by using include-files.
6. When the data packet has been transmitted, the TWINT Flag in TWCR is set, and
7. The application software should now examine the value of TWSR, to make sure that the
• When the TWI has finished an operation and expects application response, the TWINT Flag
• When the TWINT Flag is set, the user must update all TWI Registers with the value relevant
• After all TWI Register updates and other pending application software tasks have been
is set. The SCL line is pulled low until TWINT is cleared.
for the next TWI bus cycle. As an example, TWDR must be loaded with the value to be
transmitted in the next bus cycle.
completed, TWCR is written. When writing TWCR, the TWINT bit should be set. Writing a
one to TWINT clears the flag. The TWI will then commence executing whatever operation
was specified by the TWCR setting.
that the TWINT bit is set in the value written. Writing a one to TWINT clears the flag.
The TWI will not start any operation as long as the TWINT bit in TWCR is set. Immedi-
ately after the application has cleared TWINT, the TWI will initiate transmission of the
data packet.
TWSR is updated with a status code indicating that the data packet has successfully
been sent. The status code will also reflect whether a Slave acknowledged the packet
or not.
data packet was successfully transmitted, and that the value of the ACK bit was as
expected. If TWSR indicates otherwise, the application software might take some spe-
cial action, like calling an error routine. Assuming that the status code is as expected,
the application must write a specific value to TWCR, instructing the TWI hardware to
transmit a STOP condition. Which value to write is described later on. However, it is
important that the TWINT bit is set in the value written. Writing a one to TWINT clears
the flag. The TWI will not start any operation as long as the TWINT bit in TWCR is set.
Immediately after the application has cleared TWINT, the TWI will initiate transmission
of the STOP condition. Note that TWINT is NOT set after a STOP condition has been
sent.
C Example
TWCR = (1<<TWINT)|(1<<TWSTA)|
while (!(TWCR & (1<<TWINT)))
(1<<TWEN)
;
Comments
Send START condition
Wait for TWINT Flag set. This
indicates that the START
condition has been transmitted
ATtiny48/88
139