ATmega644R212 Atmel Corporation, ATmega644R212 Datasheet - Page 14

• Manufacturer Part Number: ATmega644R212
• Manufacturer: Atmel Corporation

Specifications of ATmega644R212

• Flash (kbytes): 64 Kbytes
• Max. Operating Frequency: 20 MHz
• Max I/o Pins: 32
• Spi: 3
• Twi (i2c): 1
• Uart: 1
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: AES
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 3
• Frequency Band: 700/800/900MHz
• Max Data Rate (mb/s): 1
• Antenna Diversity: No
• External Pa Control: Yes
• Power Output (dbm): 10
• Receiver Sensitivity (dbm): -110
• Receive Current Consumption (ma): 9.0
• Transmit Current Consumption (ma): 18 at 5dBm
• Link Budget (dbm): 120

4.5.1
4.5.2
4.6
8011O–AVR–07/10
Instruction Execution Timing
SPH and SPL – Stack Pointer High and Stack pointer Low
RAMPZ – Extended Z-pointer Register for ELPM/SPM
Note:
Table 4-2.
For ELPM/SPM instructions, the Z-pointer is a concatenation of RAMPZ, ZH, and ZL, as shown
in Figure 4-4. Note that LPM is not affected by the RAMPZ setting.
Figure 4-4.
The actual number of bits is implementation dependent. Unused bits in an implementation will
always read as zero. For compatibility with future devices, be sure to write these bits to zero.
This section describes the general access timing concepts for instruction execution. The AVR
CPU is driven by the CPU clock clk
chip. No internal clock division is used.
Figure 4-5 on page 15
by the Harvard architecture and the fast-access Register File concept. This is the basic pipelin-
ing concept to obtain up to 1 MIPS per MHz with the corresponding unique results for functions
per cost, functions per clocks, and functions per power-unit.
Bit
0x3E (0x5E)
0x3D (0x5D)
Read/Write
Initial Value
Bit
0x3B (0x5B)
Read/Write
Initial Value
Bit (Individually)
Bit (Z-pointer)
1. Initial values respectively for the ATmega164P/324P/644P.
Stack Pointer size
The Z-pointer used by ELPM and SPM
RAMPZ7
R/W
R/W
SP7
15
7
0
R
–
7
0
1
ATmega164P
ATmega324P
ATmega644P
23
7
Device
shows the parallel instruction fetches and instruction executions enabled
RAMPZ6
R/W
SP6
R/W
RAMPZ
14
6
0
R
–
6
0
1
RAMPZ5
R/W
SP5
R/W
CPU
5
0
13
R
–
5
0
1
16
0
, directly generated from the selected clock source for the
RAMPZ4
0/0/1
R/W
SP12
SP4
R/W
R/W
4
0
12
4
1
(1)
15
7
ATmega164P/324P/644P
RAMPZ3
R/W
0/1/0
SP11
SP3
R/W
R/W
3
0
11
3
1
(1)
ZH
RAMPZ2
R/W
1/0/0
SP10
2
0
SP2
R/W
R/W
10
Stack Pointer size
2
1
(1)
0
8
SP[10:0]
SP[11:0]
SP[12:0]
RAMPZ1
R/W
SP9
SP1
R/W
R/W
1
0
9
1
0
1
7
7
RAMPZ0
R/W
SP8
SP0
R/W
R/W
0
0
8
0
0
1
ZL
RAMPZ
SPH
SPL
0
0
14