ATmega32M1 Atmel Corporation, ATmega32M1 Datasheet - Page 62

• Manufacturer Part Number: ATmega32M1
• Manufacturer: Atmel Corporation

Specifications of ATmega32M1

• Flash (kbytes): 32 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

12.2.5
12.2.6
62
ATmega16M1/32M1/64M1
PCIFR – Pin Change Interrupt Flag Register
PCMSK3 – Pin Change Mask Register 3
• Bit 7:4 - Res: Reserved
These bits are reserved and will always read as zero.
• Bit 3 - PCIF3: Pin Change Interrupt Flag 3
When a logic change on any PCINT26:24 pin triggers an interrupt request, PCIF3 becomes set
(one). If the I-bit in SREG and the PCIE3 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 2 - PCIF2: Pin Change Interrupt Flag 2
When a logic change on any PCINT23:16 pin triggers an interrupt request, PCIF2 becomes set
(one). If the I-bit in SREG and the PCIE2 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 1 - PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15:8 pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 0 - PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF0 becomes set
(one). If the I-bit in SREG and the PCIE0 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 7:3 – Res: Reserved
These bits are reserved and will always read as zero.
• Bit 2:0 – PCINT26:24: Pin Change Enable Mask 26:24
Each PCINT26:24-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT26:24 is set and the PCIE3 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT23:24 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
R/W
7
0
-
R
7
–
0
R/W
6
0
-
R
6
–
0
R/W
5
0
-
R
5
–
0
R/W
4
0
-
R
4
–
0
R/W
PCIF3
3
0
-
R
3
0
PCINT26
PCIF2
R/W
R/W
2
0
2
0
PCINT25
PCIF1
R/W
R/W
1
0
1
0
PCINT24
PCIF0
R/W
R/W
0
0
0
0
8209D–AVR–11/10
PCMSK3
PCIFR