ATmega16M1 Automotive Atmel Corporation, ATmega16M1 Automotive Datasheet - Page 279

• Manufacturer Part Number: ATmega16M1 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega16M1 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

24. Boot Loader Support – Read-While-Write Self-Programming
24.1
24.2
24.2.1
24.2.2
7647G–AVR–09/11
ATmega16/32/64/M1/C1
Boot Loader Features
Application and Boot Loader Flash Sections
Application Section
BLS – Boot Loader Section
In ATmega16/32/64/M1/C1, the Boot Loader Support provides a real Read-While-Write
Self-Programming mechanism for downloading and uploading program code by the MCU
itself. This feature allows flexible application software updates controlled by the MCU using a
Flash-resident Boot Loader program. The Boot Loader program can use any available data
interface and associated protocol to read code and write (program) that code into the Flash
memory, or read the code from the program memory. The program code within the Boot
Loader section has the capability to write into the entire Flash, including the Boot Loader
memory. The Boot Loader can thus even modify itself, and it can also erase itself from the
code if the feature is not needed anymore. The size of the Boot Loader memory is configu-
rable with fuses and the Boot Loader has two separate sets of Boot Lock bits which can be set
independently. This gives the user a unique flexibility to select different levels of protection.
•
•
•
•
•
•
•
Note:
The Flash memory is organized in two main sections, the Application section and the Boot
Loader section (see
BOOTSZ Fuses as shown in
can have different level of protection since they have different sets of Lock bits.
The Application section is the section of the Flash that is used for storing the application code.
The protection level for the Application section can be selected by the application Boot Lock
bits (Boot Lock bits 0), see
any Boot Loader code since the SPM instruction is disabled when executed from the Applica-
tion section.
While the Application section is used for storing the application code, the The Boot Loader
software must be located in the BLS since the SPM instruction can initiate a programming
when executing from the BLS only. The SPM instruction can access the entire Flash, including
the BLS itself. The protection level for the Boot Loader section can be selected by the Boot
Loader Lock bits (Boot Lock bits 1), see
Read-While-Write Self-Programming
Flexible Boot Memory Size
High Security (Separate Boot Lock Bits for a Flexible Protection)
Separate Fuse to Select Reset Vector
Optimized Page
Code Efficient Algorithm
Efficient Read-Modify-Write Support
1. A page is a section in the Flash consisting of several bytes (see
used during programming. The page organization does not affect normal operation.
(1)
Size
Figure
Table 24-2 on page
24-2). The size of the different sections is configured by the
Table 24-7 on page 292
Atmel ATmega16/32/64/M1/C1
Table 24-3 on page
283. The Application section can never store
and
Figure
283.
24-2. These two sections
Table 25-12 on page
303)
279