AT90PWM3B Atmel Corporation, AT90PWM3B Datasheet - Page 348

• Manufacturer Part Number: AT90PWM3B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM3B

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 1
• Pwm Channels: 12
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

32. Errata
32.1
348
AT90PWM2&3 Rev. A (Mask Revision)
AT90PWM2/3/2B/3B
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1. PGM: PSCnRB Fuse
2. PSC: Prescaler
3. PSC: PAOCnA and PAOCnB Register Bits (Asynchronous output control)
4. PSC: PEVnA/B flag bits
PGM: PSCxRB Fuse
PSC: Prescaler
PSC: PAOCnA and PAOCnB Register Bits (Asynchronous output control)
PSC: PEVxA/B Flag Bits
PSC: Output Polarity in Centered Mode
PSC: Output Activity
VREF
DALI
DAC: Register Update
DAC: Output spikes
DAC driver: Output Voltage linearity
ADC: Conversion accuracy
Analog comparator: Offset value
Analog comparator: Output signal
PSC: Autolock modes
DALI: 17th bit detection
PSC: One ramp mode with PSC input mode 8
The use of PSCnRB fuse can make the parallel ISP fail.
Workaround:
When PSCnRB fuses are used, use the serial programming mode to load a new program
version.
The use of PSC's prescaler have the following effects :
It blocks the sample of PSC inputs until the two first cycles following the set of PSC run bit.
A fault is not properly transferred to other (slave) PSC.
Workaround:
Clear the prescaler PPREx bit when stopping the PSC (prun = 0), and set them to appropri-
ate value when starting the PSC (prun = 1), these bits are in the same PCTL register
Do not use the prescaler when a fault on one PSC should affect other PSC’s
These register bits are malfunctioning.
Workaround:
Do not use this feature.
These flags are set when a fault arises, but can also be set again during the fault itself.
Workaround:
Don't clear these flags before the fault disappears.
4317J–AVR–08/10