AT90PWM3B Atmel Corporation, AT90PWM3B Datasheet - Page 272

• Manufacturer Part Number: AT90PWM3B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM3B

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 1
• Pwm Channels: 12
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

24.7
272
Self-Programming the Flash
AT90PWM2/3/2B/3B
Figure 24-3. Addressing the Flash During SPM
Note:
The program memory is updated in a page by page fashion. Before programming a page with
the data stored in the temporary page buffer, the page must be erased. The temporary page buf-
fer is filled one word at a time using SPM and the buffer can be filled either before the Page
Erase command or between a Page Erase and a Page Write operation:
Alternative 1, fill the buffer before a Page Erase
•
•
•
Alternative 2, fill the buffer after Page Erase
•
•
•
If only a part of the page needs to be changed, the rest of the page must be stored (for example
in the temporary page buffer) before the erase, and then be rewritten. When using alternative 1,
the Boot Loader provides an effective Read-Modify-Write feature which allows the user software
to first read the page, do the necessary changes, and then write back the modified data. If alter-
native 2 is used, it is not possible to read the old data while loading since the page is already
erased. The temporary page buffer can be accessed in a random sequence. It is essential that
the page address used in both the Page Erase and Page Write operation is addressing the same
page. See
code example.
Fill temporary page buffer
Perform a Page Erase
Perform a Page Write
Perform a Page Erase
Fill temporary page buffer
Perform a Page Write
Z - REGISTER
1. The different variables used in
PROGRAM MEMORY
“Simple Assembly Code Example for a Boot Loader” on page 275
BIT
PAGE
PROGRAM
COUNTER
15
PAGE ADDRESS
WITHIN THE FLASH
ZPCMSB
PCMSB
PCPAGE
Figure 24-3
ZPAGEMSB
PAGEMSB
PCWORD
WORD ADDRESS
WITHIN A PAGE
(1)
are listed in
1
0
0
INSTRUCTION WORD
PAGE
Table 24-8 on page
PCWORD[PAGEMSB:0]:
00
01
02
PAGEEND
278.
for an assembly
4317J–AVR–08/10