AT89C5131A-L Atmel Corporation, AT89C5131A-L Datasheet - Page 66
AT89C5131A-L
Manufacturer Part Number
AT89C5131A-L
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT89C5130A-M.pdf
(34 pages)
2.AT89C5131A-L.pdf
(4 pages)
3.AT89C5131A-L.pdf
(186 pages)
Specifications of AT89C5131A-L
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
48 MHz
Cpu
8051-12C
Max I/o Pins
34
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
1
Sram (kbytes)
1.25
Eeprom (bytes)
1024
Self Program Memory
API
Operating Voltage (vcc)
3.0 to 3.6
Timers
4
Isp
UART/USB
Watchdog
Yes
- Current page: 66 of 186
- Download datasheet (2Mb)
Serial I/O Port
Framing Error Detection
66
AT89C5131A-L
The serial I/O port in the AT89C5131A-L is compatible with the serial I/O port in the
80C52.
It provides both synchronous and asynchronous communication modes. It operates as
an Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex
modes (modes 1, 2 and 3). Asynchronous transmission and reception can occur simul-
taneously and at different baud rates.
Serial I/O port includes the following enhancements:
•
•
Framing bit error detection is provided for the three asynchronous modes (modes 1, 2
and 3). To enable the framing bit error detection feature, set SMOD0 bit in PCON regis-
ter (see Figure 34).
Figure 34. Framing Error Block Diagram
When this feature is enabled, the receiver checks each incoming data frame for a valid
stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous
transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in
SCON register (See Table 56) bit is set.
Software may examine FE bit after each reception to check for data errors. Once set,
only software or a reset can clear FE bit. Subsequently received frames with valid stop
bits cannot clear FE bit. When FE feature is enabled, RI rises on stop bit instead of the
last data bit (See Figure 35 and Figure 36).
Figure 35. UART Timings in Mode 1
Framing error detection
Automatic address recognition
SMOD0 = X
SMOD0 = 1
RXD
SM0/FE
FE
RI
SMOD1
SMOD0
SM1
Start
Bit
D0
SM2
-
D1
REN
Set FE Bit if Stop Bit is 0 (framing error) (SMOD0 = 1)
SM0 to UART Mode Control (SMOD0 = 0)
POF
To UART Framing Error Control
D2
TB8
GF1
D3
Data Byte
RB8
GF0
D4
D5
PD
TI
D6
IDL
RI
D7
SCON (98h)
PCON (87h)
Stop
Bit
4338F–USB–08/07
Related parts for AT89C5131A-L
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-Bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Microcontroller With 4k Bytes Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC 8051 MCU 64K FLASH 44-VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 24SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 32VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K 64BGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 64K 52PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 64K 64VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU 16K FLASH 32-VQFP
Manufacturer:
Atmel
Datasheet: