LPC2214FBD144 NXP Semiconductors, LPC2214FBD144 Datasheet - Page 15

• Manufacturer Part Number: LPC2214FBD144
• Manufacturer: NXP Semiconductors

Specifications of LPC2214FBD144

• Cpu Family: LPC2000
• Device Core: ARM7TDMI-S
• Device Core Size: 16/32Bit
• Frequency (max): 60MHz
• Interface Type: I2C/SPI
• Program Memory Type: Flash
• Program Memory Size: 256KB
• Total Internal Ram Size: 16KB
• # I/os (max): 112
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/2.5/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Lead Free Status / Rohs Status: Compliant

NXP Semiconductors
LPC2212_2214_4
Product data sheet
6.5.1 Interrupt sources
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to produce
the IRQ signal to the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping there. If any of the vectored IRQs are requesting, the
VIC provides the address of the highest-priority requesting IRQs service routine,
otherwise it provides the address of a default routine that is shared by all the non-vectored
IRQs. The default routine can read another VIC register to see what IRQs are active.
Table 4
one interrupt line connected to the Vectored Interrupt Controller, but may have several
internal interrupt flags. Individual interrupt flags may also represent more than one
interrupt source.
Table 4.
Block
WDT
-
ARM Core
ARM Core
Timer 0
Timer 1
UART0
UART1
PWM0
I
SPI0
SPI1 and SSP
PLL
RTC
System Control
ADC
2
C-bus
lists the interrupt sources for each peripheral function. Each peripheral device has
Interrupt sources
[1]
Flag(s)
Watchdog Interrupt (WDINT)
Reserved for software interrupts only
EmbeddedICE, DbgCommRx
EmbeddedICE, DbgCommTx
Match 0 to 3 (MR0, MR1, MR2, MR3)
Match 0 to 3 (MR0, MR1, MR2, MR3)
Rx Line Status (RLS)
Transmit Holding Register empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Rx Line Status (RLS)
Transmit Holding Register empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Modem Status Interrupt (MSI)
Match 0 to 6 (MR0, MR1, MR2, MR3, MR4, MR5, MR6)
SI (state change)
SPIF, MODF
SPIF, MODF and TXRIS, RXRIS, RTRIS, RORRIS
PLL Lock (PLOCK)
RTCCIF (Counter Increment), RTCALF (Alarm)
External Interrupt 0 (EINT0)
External Interrupt 1 (EINT1)
External Interrupt 2 (EINT2)
External Interrupt 3 (EINT3)
ADC
Rev. 04 — 3 January 2008
16/32-bit ARM microcontrollers
LPC2212/2214
© NXP B.V. 2008. All rights reserved.
VIC channel #
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
15 of 45