PIC24FJ64GA002-I/SO Microchip Technology Inc., PIC24FJ64GA002-I/SO Datasheet - Page 92

• Manufacturer Part Number: PIC24FJ64GA002-I/SO
• Description: MCU, 16-Bit, 28-Pin, 64KB Flash, 8KB RAM, 21 I/O, Nanowatt
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ64GA002-I/SO

• A/d Inputs: 10 Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 21
• Interface: I2C/SPI/UART
• Memory Capacity: 64 Kbytes
• Memory Type: Flash
• Number Of Bits: 16
• Number Of Inputs: 21
• Number Of Pins: 28
• Package Type: 28-pin SOIC
• Programmable Memory: 64K Bytes
• Ram Size: 8K Bytes
• Speed: 32 MHz
• Timers: 5-16-bit
• Voltage, Range: 2-3.6 V
• Voltage, Rating: 2-3.6 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC24FJ64GA004 FAMILY
REGISTER 7-1:
DS39881B-page 90
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-12
bit 11
bit 10-8
bit 7
bit 6
bit 5
bit 4
Note 1:
CLKLOCK
R/SO-0
U-0
—
2:
3:
Reset values for these bits are determined by the FNOSC Configuration bits.
The state of the IOLOCK bit can only be changed once an unlocking sequence has been executed. In
addition, if the IOL1WAY Configuration bit is ‘1’, once the IOLOCK bit is set, it cannot be cleared.
Also resets to ‘0’ during any valid clock switch or whenever a non-PLL clock mode is selected.
Unimplemented: Read as ‘0’
COSC2:COSC0: Current Oscillator Selection bits
111 = Fast RC Oscillator with Postscaler (FRCDIV)
110 = Reserved
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL)
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator with Postscaler and PLL module (FRCPLL)
000 = Fast RC Oscillator (FRC)
Unimplemented: Read as ‘0’
NOSC2:NOSC0: New Oscillator Selection bits
111 = Fast RC Oscillator with Postscaler (FRCDIV)
110 = Reserved
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL)
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator with Postscaler and PLL module (FRCPLL)
000 = Fast RC Oscillator (FRC)
CLKLOCK: Clock Selection Lock Enabled bit
If FSCM is enabled (FCKSM1 = 1):
1 = Clock and PLL selections are locked
0 = Clock and PLL selections are not locked and may be modified by setting the OSWEN bit
If FSCM is disabled (FCKSM1 = 0):
Clock and PLL selections are never locked and may be modified by setting the OSWEN bit.
IOLOCK: I/O Lock Enable bit
1 = I/O lock is active
0 = I/O lock is not active
LOCK: PLL Lock Status bit
1 = PLL module is in lock or PLL module start-up timer is satisfied
0 = PLL module is out of lock, PLL start-up timer is running or PLL is disabled
Unimplemented: Read as ‘0’
IOLOCK
COSC2
R/W-0
R-0
OSCCON: OSCILLATOR CONTROL REGISTER
(2)
CO = Clear-Only bit
W = Writable bit
‘1’ = Bit is set
COSC1
LOCK
R-0
R-0
(3)
(3)
(2)
COSC0
R-0
U-0
Preliminary
—
U = Unimplemented bit, read as ‘0’
SO = Set-Only bit
‘0’ = Bit is cleared
R/CO-0
(1)
U-0
CF
—
R/W-x
NOSC2
U-0
—
(1)
© 2007 Microchip Technology Inc.
x = Bit is unknown
SOSCEN
R/W-x
NOSC1
R/W-0
(1)
R/W-x
OSWEN
NOSC0
R/W-0
(1)
bit 8
bit 0