PIC24FJ256GB206-I/MR Microchip Technology Inc., PIC24FJ256GB206-I/MR Datasheet - Page 283

• Manufacturer Part Number: PIC24FJ256GB206-I/MR
• Description: 16-bit, 256KB Flash, 96K RAM, USB, 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256GB206-I/MR

• A/d Inputs: 16 Channel, 10-bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 52
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin QFN
• Programmable Memory: 256K Bytes
• Ram Size: 98K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to 85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

20.1.3
REGISTER 20-1:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9-8
Note 1:
RTCEN
R/W-0
R/W-0
CAL7
2:
3:
(2)
The RCFGCAL register is only affected by a POR.
A write to the RTCEN bit is only allowed when RTCWREN = 1.
This bit is read-only. It is cleared to ‘0’ on a write to the lower half of the MINSEC register.
RTCC CONTROL REGISTERS
RTCEN: RTCC Enable bit
1 = RTCC module is enabled
0 = RTCC module is disabled
Unimplemented: Read as ‘0’
RTCWREN: RTCC Value Registers Write Enable bit
1 = RTCVALH and RTCVALL registers can be written to by the user
0 = RTCVALH and RTCVALL registers are locked out from being written to by the user
RTCSYNC: RTCC Value Registers Read Synchronization bit
1 = RTCVALH, RTCVALL and ALCFGRPT registers can change while reading due to a rollover ripple
0 = RTCVALH, RTCVALL or ALCFGRPT registers can be read without concern over a rollover ripple
HALFSEC: Half-Second Status bit
1 = Second half period of a second
0 = First half period of a second
RTCOE: RTCC Output Enable bit
1 = RTCC output is enabled
0 = RTCC output is disabled
RTCPTR<1:0>: RTCC Value Register Window Pointer bits
Points to the corresponding RTCC Value registers when reading the RTCVALH and RTCVALL registers.
The RTCPTR<1:0> value decrements on every read or write of RTCVALH until it reaches ‘00’.
RTCVAL<15:8>:
11 = Reserved
10 = MONTH
01 = WEEKDAY
00 = MINUTES
RTCVAL<7:0>:
11 = YEAR
10 = DAY
01 = HOURS
00 = SECONDS
R/W-0
CAL6
resulting in an invalid data read. If the register is read twice and results in the same data, the data
can be assumed to be valid.
U-0
—
RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER
HSC = Hardware Settable/Clearable bit
W = Writable bit
‘1’ = Bit is set
RTCWREN
R/W-0
R/W-0
CAL5
(2)
RTCSYNC
R-0, HSC
PIC24FJ256GB210 FAMILY
R/W-0
CAL4
(3)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
HALFSEC
R-0, HSC
R/W-0
CAL3
(3)
RTCOE
R/W-0
R/W-0
CAL2
x = Bit is unknown
R/W-0, HSC R/W-0, HSC
RTCPTR1
R/W-0
CAL1
DS39975A-page 283
(1)
RTCPTR0
R/W-0
CAL0
bit 8
bit 0