PIC24FJ256GB206-I/MR Microchip Technology Inc., PIC24FJ256GB206-I/MR Datasheet - Page 264

• Manufacturer Part Number: PIC24FJ256GB206-I/MR
• Description: 16-bit, 256KB Flash, 96K RAM, USB, 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256GB206-I/MR

• A/d Inputs: 16 Channel, 10-bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 52
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin QFN
• Programmable Memory: 256K Bytes
• Ram Size: 98K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to 85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC24FJ256GB210 FAMILY
REGISTER 18-19: U1EIR: USB ERROR INTERRUPT STATUS REGISTER
DS39975A-page 264
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/K-0, HS
Note:
BTSEF
U-0
—
Individual bits can only be cleared by writing a ‘1’ to the bit position as part of a word write operation on the
entire register. Using Boolean instructions or bitwise operations to write to a single bit position will cause
all set bits at the moment of the write to become cleared.
Unimplemented: Read as ‘0’
BTSEF: Bit Stuff Error Flag bit
1 = Bit stuff error has been detected
0 = No bit stuff error has been detected
Unimplemented: Read as ‘0’
DMAEF: DMA Error Flag bit
1 = A USB DMA error condition is detected
0 = No DMA error
BTOEF: Bus Turnaround Time-out Error Flag bit
1 = Bus turnaround time-out has occurred
0 = No bus turnaround time-out
DFN8EF: Data Field Size Error Flag bit
1 = Data field was not an integral number of bytes
0 = Data field was an integral number of bytes
CRC16EF: CRC16 Failure Flag bit
1 = CRC16 failed
0 = CRC16 passed
For Device mode:
CRC5EF: CRC5 Host Error Flag bit
1 = Token packet is rejected due to CRC5 error
0 = Token packet is accepted (no CRC5 error)
For Host mode:
EOFEF: End-of-Frame Error Flag bit
1 = End-of-Frame error has occurred
0 = End-of-Frame interrupt is disabled
PIDEF: PID Check Failure Flag bit
1 = PID check failed
0 = PID check passed
than the number of received bytes, the received data is truncated
U-0
U-0
—
—
U = Unimplemented bit, read as ‘0’
K = Write ‘1’ to clear bit
‘1’ = Bit is set
R/K-0, HS
DMAEF
U-0
—
R/K-0, HS
BTOEF
U-0
—
; t
HS = Hardware Settable bit
‘0’ = Bit is cleared
R/K-0, HS
he data size indicated by the BD byte count field is less
DFN8EF
U-0
—
CRC16EF
R/K-0, HS
U-0
—
 2010 Microchip Technology Inc.
x = Bit is unknown
R/K-0, HS
CRC5EF
EOFEF
U-0
—
R/K-0, HS
PIDEF
U-0
—
bit 8
bit 0