IDT82V2044EPFG8 IDT, Integrated Device Technology Inc, IDT82V2044EPFG8 Datasheet - Page 31
![IC LINE INTERFC UNIT 4CH 128TQFP](/photos/6/86/68686/idt82v2044epfg8_sml.jpg)
IDT82V2044EPFG8
Manufacturer Part Number
IDT82V2044EPFG8
Description
IC LINE INTERFC UNIT 4CH 128TQFP
Manufacturer
IDT, Integrated Device Technology Inc
Type
Line Interface Units (LIUs)r
Datasheet
1.IDT82V2044EPFG8.pdf
(73 pages)
Specifications of IDT82V2044EPFG8
Protocol
E1
Voltage - Supply
3.13 V ~ 3.47 V
Mounting Type
Surface Mount
Package / Case
128-TQFP, 128-VQFP
Screening Level
Industrial
Mounting
Surface Mount
Package Type
TQFP
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
800-1863-2
82V2044EPFG8
82V2044EPFG8
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT82V2044EPFG8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
QUAD CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.11 MICROCONTROLLER INTERFACES
isters in the device. The chip supports serial processor interface and two
kinds of parallel processor interface: Motorola non_multiplexed mode and
Intel non_multiplexed mode. By pulling pin P/S to low or to High, the micro-
controller interface can be set to work in serial mode or in parallel mode
respectively. Refer to
CHARACTERISTICS
3.11.1 PARALLEL MICROCONTROLLER INTERFACE
INT/MOT is used to select the operating mode of the parallel microcontroller
The microcontroller interface provides access to read and write the reg-
The interface is compatible with Motorola or Intel microcontroller. Pin
SDO
SDI
CS
SCLK
A0
A1
for details.
7 MICROCONTROLLER INTERFACE TIMING
A2
address byte
A3
A4
Figure-20 Serial Processor Interface Function Timing
A5
remains high impedance
A6
A7
R/W
D
o
command byte
n
31
' t
interface. When pin INT/MOT is pulled to Low, the parallel microcontroller
interface is configured for Motorola compatible hosts. When High, it is for
Intel compatible microcontrollers.
3.11.2 SERIAL MICROCONTROLLER INTERFACE
(control pin for the selection of serial clock active edge). By pulling P/S pin
to LOW, the device operates in the serial host Mode. In this mode, the reg-
isters are programmed through a 24-bit word which contains an 8-bit
address byte (A0~A7), a subsequent 8-bit command byte (bit R/W) and an
8-bit data byte (D0~D7). When bit R/W is ‘1’, data is read out from pin SDO.
When bit R/W is ‘0’, data is written into SDI pin. Refer to Figure-20.
The serial interface pins include SCLK, SDI, SDO, CS as well as SCLKE
C
a
r e
D0
D0
D1
D1
input data byte (R/W=0)
Output data byte (R/W=1)
D2
D2
D3
D3
TEMPERATURE RANGES
D4
D4
D5
D5
D6
D6
INDUSTRIAL
D7
D7