PIC16F84A-04/P Microchip Technology Inc., PIC16F84A-04/P Datasheet - Page 15

• Manufacturer Part Number: PIC16F84A-04/P
• Description: 18 PIN, 1.75 KB FLASH, 68 RAM, 13 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F84A-04/P

• Cpu Speed: 5 MIPS
• Eeprom Memory: 64 Bytes
• Input Output: 13
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 18-pin PDIP
• Programmable Memory: 1.75K Bytes
• Ram Size: 68 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

3.0
The EEPROM data memory is readable and writable
during normal operation (full V
is not directly mapped in the register file space. Instead
it is indirectly addressed through the Special Function
Registers. There are four SFRs used to read and write
this memory. These registers are:
• EECON1
• EECON2 (not a physically implemented register)
• EEDATA
• EEADR
EEDATA holds the 8-bit data for read/write, and
EEADR holds the address of the EEPROM location
being accessed. PIC16F84A devices have 64 bytes of
data EEPROM with an address range from 0h to 3Fh.
REGISTER 3-1:
2001 Microchip Technology Inc.
DATA EEPROM MEMORY
bit 7-5
bit 4
bit 3
bit 2
bit 1
bit 0
EECON1 REGISTER (ADDRESS 88h)
Unimplemented: Read as '0'
EEIF: EEPROM Write Operation Interrupt Flag bit
1 = The write operation completed (must be cleared in software)
0 = The write operation is not complete or has not been started
WRERR: EEPROM Error Flag bit
1 = A write operation is prematurely terminated
0 = The write operation completed
WREN: EEPROM Write Enable bit
1 = Allows write cycles
0 = Inhibits write to the EEPROM
WR: Write Control bit
1 = Initiates a write cycle. The bit is cleared by hardware once write is complete. The WR bit
0 = Write cycle to the EEPROM is complete
RD: Read Control bit
1 = Initiates an EEPROM read RD is cleared in hardware. The RD bit can only be set (not
0 = Does not initiate an EEPROM read
bit 7
Legend:
R = Readable bit
- n = Value at POR
U-0
(any MCLR Reset or any WDT Reset during normal operation)
can only be set (not cleared) in software.
cleared) in software.
—
DD
range). This memory
U-0
—
U-0
—
W = Writable bit
’1’ = Bit is set
R/W-0
EEIF
The EEPROM data memory allows byte read and write.
A byte write automatically erases the location and
writes the new data (erase before write). The EEPROM
data memory is rated for high erase/write cycles. The
write time is controlled by an on-chip timer. The write-
time will vary with voltage and temperature as well as
from chip to chip. Please refer to AC specifications for
exact limits.
When the device is code protected, the CPU may
continue to read and write the data EEPROM memory.
The device programmer can no longer access
this memory.
Additional information on the Data EEPROM is avail-
able in the PICmicro™ Mid-Range Reference Manual
(DS33023).
WRERR
R/W-x
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
WREN
R/W-0
PIC16F84A
x = Bit is unknown
R/S-0
WR
DS35007B-page 13
R/S-0
RD
bit 0