PIC16F84A-04/P Microchip Technology Inc., PIC16F84A-04/P Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F84A-04/P
Manufacturer Part Number
PIC16F84A-04/P
Description
18 PIN, 1.75 KB FLASH, 68 RAM, 13 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F84A-04P.pdf
(88 pages)
Specifications of PIC16F84A-04/P
Cpu Speed
5 MIPS
Eeprom Memory
64 Bytes
Input Output
13
Memory Type
Flash
Number Of Bits
8
Package Type
18-pin PDIP
Programmable Memory
1.75K Bytes
Ram Size
68 Bytes
Speed
20 MHz
Timers
1-8-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F84A-04/P
Manufacturer:
MICROCHIP
Quantity:
1 450
PIC16F84A
2.3.1
The STATUS register contains the arithmetic status of
the ALU, the RESET status and the bank select bit for
data memory.
As with any register, the STATUS register can be the
destination for any instruction. If the STATUS register is
the destination for an instruction that affects the Z, DC
or C bits, then the write to these three bits is disabled.
These bits are set or cleared according to device logic.
Furthermore, the TO and PD bits are not writable.
Therefore, the result of an instruction with the STATUS
register as destination may be different than intended.
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as 000u u1uu (where u = unchanged).
Only the BCF, BSF, SWAPF and MOVWF instructions
should be used to alter the STATUS register (Table 7-2),
because these instructions do not affect any status bit.
REGISTER 2-1:
DS35007B-page 8
bit 7-6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
STATUS REGISTER
STATUS REGISTER (ADDRESS 03h, 83h)
bit 7
Unimplemented: Maintain as ‘0’
RP0: Register Bank Select bits (used for direct addressing)
01 = Bank 1 (80h - FFh)
00 = Bank 0 (00h - 7Fh)
TO: Time-out bit
1 = After power-up, CLRWDT instruction, or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity
is reversed)
1 = A carry-out from the 4th low order bit of the result occurred
0 = No carry-out from the 4th low order bit of the result
C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is
reversed)
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Legend:
R = Readable bit
- n = Value at POR
R/W-0
Note:
IRP
A subtraction is executed by adding the two’s complement of the second operand.
For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order
bit of the source register.
R/W-0
RP1
R/W-0
RP0
W = Writable bit
’1’ = Bit is set
R-1
TO
Note 1: The IRP and RP1 bits (STATUS<7:6>)
2: The C and DC bits operate as a borrow
3: When the STATUS register is the
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
R-1
PD
are not used by the PIC16F84A and
should be programmed as cleared. Use of
these bits as general purpose R/W bits is
NOT recommended, since this may affect
upward compatibility with future products.
and digit borrow out bit, respectively, in
subtraction. See the SUBLW and SUBWF
instructions for examples.
destination for an instruction that affects
the Z, DC or C bits, then the write to these
three bits is disabled. The specified bit(s)
will be updated according to device logic
R/W-x
Z
2001 Microchip Technology Inc.
x = Bit is unknown
R/W-x
DC
R/W-x
C
bit 0