E-STE100P STMicroelectronics, E-STE100P Datasheet - Page 15

• Manufacturer Part Number: E-STE100P
• Description: IC TRANSCEIVER 3.3V 64 TQFP
• Manufacturer: STMicroelectronics
• Type: Transceiverr

Specifications of E-STE100P

• Number Of Drivers/receivers: 1/1
• Protocol: MII
• Voltage - Supply: 3.15 V ~ 3.45 V
• Mounting Type: Surface Mount
• Package / Case: 64-TQFP, 64-VQFP
• Number Of Receivers: 1
• Data Rate: 10/100Mbps
• Operating Supply Voltage (typ): 3.3V
• Package Type: TQFP
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.45V
• Operating Supply Voltage (min): 3.15V
• Mounting: Surface Mount
• Pin Count: 64
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2143; STE100P

Table 5. Register Descriptions (continued)
7
The STE100P integrates the IEEE802.3u compliant functions of PCS (Physical Coding Sub-layer), PMA
(Physical Medium Attachment), and PMD(Physical Medium Dependent) for 100Base-TX, and the
IEEE802.3 compliant functions of Manchester encoding/decoding and transceiver for 10Base-T. All the
functions and operation schemes are described in the following sections.
7.1 100Base-TX Transmit Operation
Regarding the 100Base-TX transmission, the device provides the transmission functions of PCS, PMA,
and PMD for encoding of MII data nibbles to five-bit code-groups (4B/5B), scrambling, serialization of
scrambled code-groups, converting the serial NRZ code into NRZI code, converting the NRZI code into
MLT3 code, and then driving the MLT3 code into the category 5 Unshielded Twisted Pair cable through
an isolation transformer with the turns ratio of 1:1.
Bit #
7~3
DEVICE OPERATION
Data code-groups Encoder: In normal MII mode application, the device receives nibble type 4B data via
the TxD0~3 inputs of the MII. These inputs are sampled by the device on the rising edge of Tx-clk and
passed to the 4B/5B encoder to generate the 5B code-group used by 100Base-TX.
Idle code-groups: In order to establish and maintain the clock synchronization, the device needs to keep
transmitting signals to the medium. The device will generate Idle code-groups for transmission when there
is no real data want to be sent by MAC.
Start-of-Stream Delimiter-SSD (/J/K/): In a transmission stream, the first 16 nibbles are MAC preamble.
In order to let partner delineate the boundary of a data transmission sequence and to authenticate carrier
events, the device will replace the first 2 nibbles of the MAC preamble with /J/K/ code-groups.
End-of-Stream Delimiter-ESD (/T/R/): In order to indicate the termination of the normal data transmis-
sions, the device will insert 2 nibbles of /T/R/ code-group after the last nibble of FCS.
Scrambling: All the encoded data(including the idle, SSD, and ESD code-groups) is passed to the data
scrambler to reduce the EMI and spread the power spectrum using a 10-bit scrambler seed loaded at the
beginning.
2
1
0
MFPSE
PAD4:0
Name
---
---
PHY Address [4:0]:
The values of the PAD[4:0] pins are latched to this register at
power-up/reset. The first PHY address bit transmitted or
received is the MSB of the address (bit 4). A station
management entity connected to multiple PHY entities must
know the appropriate address of each PHY. A PHY address of
<00000> that is latched in to the part at power-up/reset will
cause the Isolate bit of the PR0 (bit 10, register address 00h)
to be set.
After power up/reset the only way to enable or disable isolate
mode is to set or clear the Isolate bit (bit 10) PR0. After power
up/reset writing <00000> to bits [4:0] of this register will not
cause the part to enter isolate mode.
reserved
MF Preamble Suppression Enable
1 = Accept management frames with pre-amble suppressed.
0 = Do not accept management frames with preamble
suppressed.
This bit also controls the value of bit 6 in PR1 (MFPS).
reserved
Descriptions
Default Val
[00001]
0
1
0
STE100P
RW Type
Strap,
R/W
R/W
RO
RO
15/31