MSO-0011P-012 NCC, MSO-0011P-012 Datasheet - Page 82

• Manufacturer Part Number: MSO-0011P-012
• Description: Socket, Relay; 11 Pin Octal, ID# SR3P-06
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0011P-012

• Number Of Contacts: 11
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

4-10
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
DUSTRONIX
Dust Collector Controls
Models DNC-T2610-010/020
FEATURES
●
●
●
●
●
●
●
CORE-10 UNIQUE FEATURES
●
●
●
●
●
The Core-10 is the main control module in the
DUSTRONIX line. The Core-10 is capable of
operating as a standalone module controlling
1 to 10 solenoids, or in combination with the
Expander-10 for up to 98 expansion modules for
a total of 990 outputs. The Expander-10 is the
expansion output board in the DUSTRONIX fam-
ily. The Expander-10 operates in combination with
the Core-10 Control Module.
ORDERING INFORMATION
Enclosure for DNC-T2610-010
Communicates via 2 wire CANbus net-
work
Universal input voltage 100-240 VAC,
50/60 Hz
10 outputs on-board, expands to 990
outputs (with expansion boards)
Solenoid current sense:
– allows automatic system setup
– senses 3 solenoids per output
– monitor up to 2970 solenoids
Diagnostic/program LEDs for “at-a-
glance” system status indication
Settable to read 0-10, 0-15, and 0-25
inches of differential pressure
Finger-safe terminations
Simple one knob programming
Non-volatile memory for program and
status storage
On-Demand operation:
– with external pressure switch (not
included)
– with external pressure sensor (not
included)
– source/sink 4 to 20 mA sensor input
3-digit, 7-segment alpha-numeric
display
Settable alarm output relay normally
open or normally closed
INPUT VOLTAGE
100 to 240 VAC
100 to 240 VAC
DUST COLLECTOR CONTROLS
ACCESSORY
PART NUMBER
DNC-T2610-010
DNC-T2610-020
™
Core-10/Expander-10
DIMENSIONS
10” x 8” x 6”
10 on a twisted pair of wires using CANbus archi-
tecture which provides robust noise immunity.
Two rotary switches on the Expander-10 are used
to set and provide visual indication of the address
assigned.
with input from an external pressure sensor (4 to
20 mA) or a pressure switch (not included), or it
can operate in the Continuous mode by use of a
jumper across the pressure switch input. A switch
can also be connected to the pressure switch
input to act as a bypass switch. Input for a cycle
down switch is also provided to allow for end-of-
operation cleaning.
one-button programming. This single push-but-
ton/encoder is used to select operating param-
eters. LEDs indicate program function. The
push-button is also used to view alarm conditions
and cancel the alarm output. Operating and pro-
gramming information is displayed on a 3-digit
7-segment display. The compact size of the
Core-10 and the Expander-10 allows mounting in
enclosures as small as 8” x 6”.
Programmable Parameters:
●
●
●
●
●
●
●
●
●
Status LEDs: when illuminated
●
The Expander-10 communicates with the Core-
The Core-10 can operate in On-Demand mode
A unique feature of the Core-10 is its simple
Solenoid ON-Time/OFF-Time
Number of cycle down cycles
Cycle down time delay
Run/Standby: enable/disable outputs
Differential pressure high setpoint/low
setpoint
Differential pressure high alarm setpoint/
low alarm setpoint
Alarm contact (normally open or normally
closed)
Differential Pressure Sensor Select:
10, 15, 25 in. w.c.
Output: 1 to 990 manual or auto-config-
ured
Differential Pressure: Display indicates
 P
BOX-A1008-CHSC
BOX-A1008-CHNF
PART NUMBER
●
●
●
●
●
●
DUSTRONIX “Kit” Configurations
1.
2.
3.
4.
Output: Display indicates cur-
rent output
Alarm (System Status):  P or
Solenoid Fault
Output Pulsing: Display indi-
cates output being pulsed
Cycle Down: Unit in cycle down
mode
Output Status: Unit pulsing
solenoids
CANbus Status: CANbus trans-
mission activity
DNC-T2610-N4A: Includes
Core-10, PS700, 3-position
switch, NEMA 4 10”x8”x6” metal
enclosure with cutouts, bulk-
head fittings, mounting chassis,
mounting
DNC-T2610-N4XA: Same as
above but mounted in fiberglass
enclosure
DNC-T2610-N4B: Same as Kit
1 but also includes Expander-10
module
DNC-T2610-N4XB: Same as
Kit 3 but mounted in fiberglass
enclosure