MSO-0011P-012 NCC, MSO-0011P-012 Datasheet - Page 33

• Manufacturer Part Number: MSO-0011P-012
• Description: Socket, Relay; 11 Pin Octal, ID# SR3P-06
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0011P-012

• Number Of Contacts: 11
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
ORDERING INFORMATION
Delay On Break
Z3 Series
FEATURES
●
●
●
●
●
●
●
●
●
●
●
Operating Logic: Voltage is applied to the
timer at all times. Upon a closure of a nor-
mally open isolated start switch, the output
relay is activated and remains so as long as
the switch is kept closed. When the start
switch is opened, timing starts. At the end
of the preset time delay, the output relay is
deactivated and the timer is ready for a new
cycle.
Note: 1) Do not apply voltage or ground to the start switch; 2)
Switch leads should be shielded when running close to other
wires; 3) If the start switch is re-closed during timing, the timer
will reset and will not start timing until start switch is opened (Start
switch supplied by customer).
LOGIC FUNCTION DIAGRAM
Input
Voltage
Start
Switch
Relay
Coil
100% functionally tested
No false contact transfer when reset
during timing
Digital timing circuit
Time delays to 5 minutes
±1% repeatability
Superior transient protection
Fast-on terminals for quick installation
Low cost, open board construction
Fiberglass reinforced circuit board
Trimpot on-board with sealed cermet
element
3 to 300 sec.
TIME RANGE
Closed
Open
On
Off
On
Off
Delay On Break Function
File #E59090
Timing
Z3T-00300-061
120 VAC
(Retriggerable)
SPECIFICATIONS
TIME DELAY
Adjustment: Trimpot, factory fixed on spe-
cial order (min. order required)
Range: 3 to 300 sec.
Repeatability: ±1% at constant temperature
Accuracy:
Maximum time -0%, +10%
Minimum time +0%, -50%
Reset Time: 300 ms max.
Start Switch Closure Time: 20 ms to initiate tim-
ing; 50 ms to reset delay during timing
INPUT
Operating Voltage: 120 VAC ±10%
Power Consumption: 3 VA max.
Frequency: 50/60 Hz
OUTPUT
Type: Relay contacts, DPDT (2 form C)
Rating: 10 A max. resistive at 240 VAC - 100 mA
at 5 VDC min. load current
Life:
Mechanical: 10,000,000 operations
Full Load: 500,000 operations
PROTECTION
Transient Voltage: Timers are protected by a 30
joule metal oxide varistor
Dielectric Breakdown: 1500 VAC, RMS min. at
60 Hz between input and outputs and between
outputs
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: .25” standoffs, #6 screw
ENVIRONMENTAL
Storage Temperature: -23°C to 70°C
Operating Temperature: -23°C to 55°C
TIME DELAY RELAYS
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
TIME ADJUST
.250 X .032 MALE 'FAST-ON'
(10 PL.)
for DC models
VOLTAGE
Polarity shown
.313 ±.032
INPUT
±.032
.313
CLEARANCE FOR #6 SCREW
(4 PL.)
R
120
N.C.
N.0.
COM
VAC
L2
L1
2.125 ±.032
START
SWITCH
+
-
START
1.500
6360
SWITCH
R
COM
N.C.
N.0.
INC
1-23
.187