MSO-0011P-012 NCC, MSO-0011P-012 Datasheet - Page 40

• Manufacturer Part Number: MSO-0011P-012
• Description: Socket, Relay; 11 Pin Octal, ID# SR3P-06
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0011P-012

• Number Of Contacts: 11
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

1-30
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
Flasher
Q8F Series
FEATURES
●
●
●
●
●
●
●
●
●
●
Operating Logic: Upon application of volt-
age to the input terminals, the load is ener-
gized for the duration of the preset time
delay. At the end of this time delay, the load
is de-energized for the duration of the pre-
set time delay. The load is then energized
again and the timer continues to repeat this
on-off cycle until input voltage is removed.
Both on and off times are the same and are
determined by Rt.
Note: 1) Rt and terminals 4 and 5 are used for external time
adjustment; 2) Remote potentiometer leads should be shielded
when running close to other wires; 3) The minimum time setting
on external resistor-adjustable time delay relays is obtained by
shorting together the external resistor terminals of the relay; 4)
The maximum time setting within tolerance limits is obtained by
using a 1 megohm resistor; 5) Timing values between the mini-
mum and maximum limits are linear with resistance within 10%;
6) Recommend 1/4 W minimum resistor be used.
ORDERING INFORMATION
Optional Potentiometer: Part Number ASY-0001M-450
Trigger time (start switch closure)
Reset time
Min. load
Max. leakage current
Voltage drop at 1 A
Power consumption
Peak 1 cycle surge
Protection
100% functionally tested
Only one timing component required
Solid state digital timing
Time delays to 5 minutes standard
20:1 maximum to minimum timing ratio
Low cost
Compact size
Superior transient protection
Flame-retardant and solvent-resistant
polyester thermoplastic housing
15 to 300 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
3 to 60 sec.
TIME DELAY RELAYS
File #E65038
Q8F-00001-321
Q8F-00005-321
Q8F-00010-321
Q8F-00060-321
Q8F-00300-321
120 VAC +10%
4.3 VA max.
30j. MOV
500 ms
500 ms
100 uA
2 mA
3.3 V
20 A
LOGIC FUNCTION DIAGRAM
Input
Voltage
Load
SPECIFICATIONS
TIME DELAY
Adjustment: External resistor, factory fixed on
special order (min. order requirement)
Range: 50 ms to 5 minutes in 5 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy:
Maximum time ±2% at Rt = 1 megohm
Minimum time +0%, -30% at Rt = 0 ohm
INPUT
Operating Voltage: 120 VAC ±10%
Frequency: 50/60 Hz
OUTPUT
Type: Solid state, normally open
Rating: 1 A steady state
Life: 100,000,000 operations
PROTECTION
Transient Voltage: Metal oxide varistor (see rat-
ing below)
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
Insulation Resistance: 100 megohms min.
between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: Surface mount with one #8 screw
ENVIRONMENTAL
Storage Temperature: -40°C to 85°C
Operating Temperature: -40°C to 65°C
Humidity: 95% relative
On
Off
On
Off
Timing
Timing
External Resistance/Time Delay Relationship
1 megohm external resistance is required to obtain
the maximum time for all ranges. To determine the
actual resistance needed to obtain the required time
delay, use the following formula:
Note: Due to component tolerances, the actual time
obtained will normally be within 5% of desired time.
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
Rt=
Tmaximum - Tminimum
Trequired - Tminimum
(3667-7)
LOAD
5
1
.25 X .032 MALE FAST-ON
2.00 SQ.
Rt
TERMINALS (5 PL.)
Polarity Shown is
L C
4
2
for DC Models
VOLTAGE
INPUT
1.25
C
L
.88
x 1,000,000 ohms
3
.170
DIA.