TDA8007BHL/C3,118 NXP Semiconductors, TDA8007BHL/C3,118 Datasheet - Page 6

• Manufacturer Part Number: TDA8007BHL/C3,118
• Description: IC INTERFACE CARD MP 48-LQFP
• Manufacturer: NXP Semiconductors

Specifications of TDA8007BHL/C3,118

• Controller Type: Multiprotocol IC Card Interface
• Interface: Parallel
• Voltage - Supply: 2.7 V ~ 6 V
• Current - Supply: 315mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-3520-2; 935272525118; TDA8007BHLBE-T

NXP Semiconductors
TDA8007BHL
Product data sheet
Table 3.
Symbol
C82
PRES2
C42
CGND2
CLK2
V
RST2
GND
V
SAP
SBP
V
SBM
AGND
SAM
V
D0 to D7
RD
CS
ALE
INT
INTAUX
AD3
AD2
AD1
WR
CC2
UP
DDA
DD
Pin description
All information provided in this document is subject to legal disclaimers.
Pin
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28, 29, 30, 31, 32, 33,
34, 35
36
37
38
39
40
41
42
43
44
Rev. 8 — 11 January 2011
…continued
Description
auxiliary I/O for ISO C8 contact (synchronous cards,
for instance) for card 2
card 2 presence contact input (active high)
auxiliary I/O for ISO C4 contact (synchronous cards,
for instance) for card 2
ground for card 2; must be connected to GND
clock output to card 2 (ISO C3 contact)
card 2 supply output voltage (ISO C1 contact)
card 2 reset output (ISO C2 contact)
ground
connection for the step-up converter capacitor;
connect a low ESR capacitor of 220 nF to AGND
contact 1 for the step-up converter; connect a low
ESR capacitor of 220 nF between pins SAP
and SAM
contact 3 for the step-up converter; connect a low
ESR capacitor of 220 nF between pins SBP
and SBM
positive analog supply voltage for the step-up
converter; may be higher than V
good quality capacitor to GND
contact 4 for the step-up converter; connect a low
ESR capacitor of 220 nF between pins SBP
and SBM
analog ground for the step-up converter
contact 2 for the step-up converter; connect a low
ESR capacitor of 220 nF between pins SAP
and SAM
positive supply voltage; decouple with a good quality
capacitor to GND
input/output of data 0-7;
TDA8007BHL/C3 in case of mulitplexed
configuration: address 0-7
read or write selection input; high for read, low for
write
enable pin; same behavior as CS\ (active low)
chip select input (active low)
TDA8007BHL/C4: Not connected;
TDA8007BHL/C3: address latch enable input in
case of multiplexed configuration, connect to V
non-multiplexed configuration
NMOS interrupt output (active low)
auxiliary interrupt input
register selection address 3 input
register selection address 2 input
register selection address 1 input
Multiprotocol IC card interface
TDA8007BHL
DD
© NXP B.V. 2011. All rights reserved.
; decouple with a
DD
6 of 51
in