AD1980JSTZ Analog Devices Inc, AD1980JSTZ Datasheet - Page 16

• Manufacturer Part Number: AD1980JSTZ
• Description: IC CODEC STEREO 6-DAC 20B 48LQFP
• Manufacturer: Analog Devices Inc
• Series: SoundMAX®r
• Type: Audio Codec '97r

Specifications of AD1980JSTZ

• Data Interface: Serial
• Resolution (bits): 16, 20 b
• Number Of Adcs / Dacs: 2 / 6
• Sigma Delta: No
• Dynamic Range, Adcs / Dacs (db) Typ: 82 / 90
• Voltage - Supply, Analog: 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.15 V ~ 3.45 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Single Supply Voltage (typ): 3.3/5V
• Single Supply Voltage (min): 3.15/4.75V
• Single Supply Voltage (max): 3.45/5.25V
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD1980
This register should be read before writing to generate a mask for only the bit(s) that need to be changed. All registers not shown and bits containing an X are
assumed to be reserved.
LPBK
MS
DRSS [1:0]
This register controls the Audio Interrupt and Paging mechanism. All registers not shown and bits containing an X are assumed to be reserved.
PG[3:0]
I0
I4
Reg
No. Name
20h
Reg
No. Name
24h Audio Interrupt
and Paging
General-Purpose X
Loopback Control. This bit enables the digital internal loopback from the ADC to the Front DAC. This feature is
normally used for test and troubleshooting.
0 = No Loopback (Default)
1 = Loopback PCM digital data from ADC output to DAC
See LBKS bit in Register 0x74 for changing the loopback path to use the Surround or Center/LFE DACs.
MIC Select. Selects Mono MIC input.
0 = Select MIC1
1 = Select MIC2
See 2CMIC bit in Register 76h to enable stereo microphone recording.
Double Rate Slot Select. The DRSS bits specify the slots for the n + 1 sample outputs. PCM L (n + 1) and PCM R
(n + 1) data are by default provided in output slots 10 and 11.
00: PCM L, R n + 1 Data is on Slots 10, 11 (reset default)
01: PCM L, R n + 1 Data is on Slots 7, 8
10: Reserved
11: Reserved
Page Selector (Read Only). This register is used to describe Page Selector capability for extended features.
Reading these bits returns 0h, which describes Page Selection as vendor specific only.
INTERRUPT ENABLE (R/W). This enables interrupt generation.
0 = Interrupt Generation is Masked (Default)
1 = Interrupt Generation is Unmasked
The S/W should not unmask the interrupt unless ensured by the AC ’97 controller that no conflict is possible with
Modem slot 12 GPI functionality.
AC ’97 2.2 compliant controllers will not likely support audio codec interrupt infrastructure. In that case, S/W could
poll the interrupt status after initiating a sense cycle and waiting for Sense Cycle Max Delay to determine if an inter-
rupting event has occurred.
INTERRUPT STATUS (R/W). This bit provides interrupt status and clear capability.
0 = Interrupt is Clear
1 = Interrupt was Generated
Interrupt event is cleared by writing a “1” to this bit. The interrupt bit will change regardless of condition of inter-
rupt enable (I0) status. An interrupt in the GPI in slot 12 in the AC link will follow this bit change when interrupt
enable (I0) is unmasked.
D15
D15
I4
D14
X
D14
X
D13
X
Audio Interrupt and Paging Mechanism Register (Index 24h)
D13 D12
X
X
D12 D11
X
DRSS1 DRSS0 X
General-Purpose Register (Index 20h)
D11
I0
D10
D10
X
D9
D9
X
–16–
D8
MS
D8
X
D7
LPBK
X
D7
D6
X
D6
X
D5
X
D5
X
D4
X
D4
X
D3
PG3
D3
X
D2
X
D2
PG2
D1
X
D1
PG1
D0
X
D0
PG0 xxxxh
REV. 0
Default
0000h
Default