LC5512MV-45FN484C Lattice, LC5512MV-45FN484C Datasheet - Page 26

• Manufacturer Part Number: LC5512MV-45FN484C
• Description: CPLD ispXPLD™ 5000MV Family 150K Gates 512 Macro Cells 275MHz EECMOS Technology 3.3V 484-Pin BGA
• Manufacturer: Lattice

Specifications of LC5512MV-45FN484C

• Package: 484BGA
• Family Name: ispXPLD™ 5000MV
• Device System Gates: 150000
• Number Of Macro Cells: 512
• Maximum Propagation Delay Time: 4.5 ns
• Number Of User I/os: 253
• Typical Operating Supply Voltage: 3.3 V
• Maximum Operating Frequency: 275 MHz
• Number Of Product Terms Per Macro: 160
• Memory Type: EEPROM/SRAM
• Ram Bits: 262144
• Operating Temperature: 0 to 90 °C

Lattice Semiconductor
Absolute Maximum Ratings
Supply Voltage (V
PLL Supply Voltage (V
Output Supply Voltage (V
IEEE 1149.1 TAP Supply Voltage (V
Input Voltage Applied
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65 to 150C . . . . . . . . . . . . . . . -65 to 150C
Junction Temperature (T
1. Stress above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional
2. Compliance with the Lattice
3. All voltages referenced to GND.
4. Overshoot and Undershoot of -2V to (V
5. A maximum of 64 I/Os per device with V
Recommended Operating Conditions
E
Hot Socketing Characteristics
V
V
T
I
1. Insensitive to sequence of V
2. 0 ð V
3. I
4. LVTTL, LVCMOS only.
Erase/Reprogram Cycle
1. Valid over commercial temperature range.
DK
J
CC
CCP
2
Symbol
operation of the device at these or any other conditions above those indicated in the operational sections of this specification
is not implied (while programming, following the programming specifications).
Symbol
CMOS Erase Reprogram Specifications
rise/fall rates for V
DK
is additive to I
CC
ð V
Input or I/O Leakage Current
CC
Supply Voltage for 1.8V Devices (ispXPLD 5000MC)
Supply Voltage for 2.5V Devices (ispXPLD 5000MB)
Supply Voltage for 3.3V Devices (ispXPLD 5000MV)
PLL Block Supply Voltage for PLL 1.8V Devices
PLL Block Supply Voltage for PLL 2.5V Devices
PLL Block Supply Voltage for PLL 3.3V Devices
Junction Temperature (Commercial Operation)
Junction Temperature (Industrial Operation)
(MAX), 0 ð V
PU
CC
CC
, I
and V
) . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
PD
4, 5
CCP
1
or I
Parameter
. . . . . . . . . . . . . . . . . . . . . -0.5 to 5.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
J
CCO,
CCO
) with Power Applied . . . -55 to 150C . . . . . . . . . . . . . . . -55 to 150C
CCO
CC
BH
) . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
Thermal Management
. Device defaults to pull-up until non-volatile cells are active.
and V
provided (V
) . . . . . . . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
ð V
CCO
CCO
(MAX)
CCJ
when V
Parameter
IHMAX
IN
IN
) . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
- V
> 3.6V is allowed.
1, 2, 3
CCO
CCO
+2) volts not to exceed 6V is permitted for a duration of <20ns.
Parameter
1, 2, 3, 4
0 ð V
)þð 3.6V.
þð 1.0V. For V
ispXPLD 5000MC
document is required.
IN
ð 3.0V
1.8V
Condition
22
CCO
> 1.0V, V
ispXPLD 5000MX Family Data Sheet
CC
min must be present. However, assumes monotonic
Min.
—
ispXPLD 5000MB/V
2.5V/3.3V
1,000
+/-50
Min.
Min.
Typ.
1.65
1.65
2.3
2.3
-40
3
3
0
+/-800
Max.
Max.
Max.
1.95
1.95
105
2.7
3.6
2.7
3.6
—
90
Cycles
Units
Units
Units
A
V
V
V
V
V
V
C
C