ADF4360-0BCPZ Analog Devices Inc, ADF4360-0BCPZ Datasheet - Page 20

• Manufacturer Part Number: ADF4360-0BCPZ
• Description: IC INTEGRATED SYNTH/VCO 24-LFCSP
• Manufacturer: Analog Devices Inc
• Type: Fanout Distribution, Integer N Synthesizer (RF)r

Specifications of ADF4360-0BCPZ

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 1:2
• Differential - Input:output: No/No
• Frequency - Max: 2.725GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 2.725GHz
• Pll Type: Frequency Synthesis
• Frequency: 2.725GHz
• Supply Current: 10mA
• Supply Voltage Range: 3V To 3.6V
• Digital Ic Case Style: LFCSP
• No. Of Pins: 24
• Operating Temperature Range: -40°C To +85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4360-0EBZ1 - BOARD EVALUATION FOR ADF4360-0
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

ADF4360-0
APPLICATIONS
FIXED FREQUENCY LO
Figure 17 shows the ADF4360-0 used as a fixed frequency LO at 2.6
GHz. The low-pass filter was designed using ADIsimPLL for a
channel spacing of 8 MHz and an open-loop bandwidth of 40 kHz.
The maximum PFD frequency of the ADF4360-0 is 8 MHz.
Because using a larger PFD frequency allows users to use a smaller
N, the in-band phase noise is reduced to as low as possible,
–100 dBc/Hz. The 40 kHz bandwidth is chosen to be just greater
than the point at which the open-loop phase noise of the VCO is
–100 dBc/Hz, thus giving the best possible integrated noise. The
typical rms phase noise (100 Hz to 100 kHz) of the LO in this con-
figuration is 0.35°. The reference frequency is from a 16 MHz
TCXO from Fox; thus, an R value of 2 is programmed. Taking into
account the high PFD frequency and its effect on the band select
logic, the band select clock divider is enabled. In this case, a value of
8 is chosen. A very simple pull-up resistor and dc blocking capaci-
tor complete the RF output stage.
INTERFACING
The ADF4360 family has a simple SPI®-compatible serial inter-
face for writing to the device. CLK, DATA, and LE control the
data transfer. When LE goes high, the 24 bits that have been
clocked into the appropriate register on each rising edge of CLK
are transferred to the appropriate latch. See Figure 2 for the
timing diagram and Table 5 for the latch truth table.
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible is 833 kHz or
one update every 1.2 µs. This is more than adequate for systems
that have typical lock times in hundreds of microseconds.
801BE-160
16MHz
FOX
1nF
10µF
1nF
4.7kΩ
1nF
51Ω
14
16
17
18
19
12
13
CPGND
C
REF
CLK
DATA
LE
C
R
1
V
V
N
C
SET
VCO
VCO
6
Figure 17. Fixed Frequency LO
IN
3
DV
8
21
DD
AGND
9
ADF4360-0
AV
V
VDD
10
2
DD
11
CE MUXOUT
23
22
DETECT
LOCK
DGND RF
20
15
RF
V
OUT
OUT
TUNE
CP
A
B
24
7
4
5
V
560pF
VCO
51Ω
1.5kΩ
8.2nF
51Ω
3kΩ
100pF
100pF
270pF
Rev. A | Page 20 of 24
ADuC812 Interface
Figure 18 shows the interface between the ADF4360 family and
the ADuC812 MicroConverter®. Because the ADuC812 is based
on an 8051 core, this interface can be used with any 8051 based
microcontroller. The MicroConverter is set up for SPI master
mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF4360 family
needs a 24-bit word, which is accomplished by writing three 8-
bit bytes from the MicroConverter to the device. When the third
byte has been written, the LE input should be brought high to
complete the transfer.
I/O port lines on the ADuC812 are also used to control power-
down (CE input) and detect lock (MUXOUT configured as lock
detect and polled by the port input). When operating in the
described mode, the maximum SCLOCK rate of the ADuC812
is 4 MHz. This means that the maximum rate at which the out-
put frequency can be changed is 166 kHz.
ADSP-21xx Interface
Figure 19 shows the interface between the ADF4360 family and
the ADSP-21xx digital signal processor. The ADF4360 family
needs a 24-bit serial word for each latch write. The easiest way
to accomplish this using the ADSP-21xx family is to use the
autobuffered transmit mode of operation with alternate fram-
ing. This provides a means for transmitting an entire block of
serial data before an interrupt is generated.
Set up the word length for 8 bits and use three memory loca-
tions for each 24-bit word. To program each 24-bit latch, store
the 8-bit bytes, enable the autobuffered mode, and write to the
transmit register of the DSP. This last operation initiates the
autobuffer transfer.
ADSP-21xx
ADuC812
I/O PORTS
I/O PORTS
SCLOCK
Figure 19. ADSP-21xx to ADF4360-x Interface
SCLOCK
Figure 18. ADuC812 to ADF4360-x Interface
MOSI
MOSI
TFS
SDATA
SDATA
SCLK
LE
CE
MUXOUT
(LOCK DETECT)
SCLK
LE
CE
MUXOUT
(LOCK DETECT)
ADF4360-x
ADF4360-x