FDC37B787-NS Standard Microsystems (SMSC), FDC37B787-NS Datasheet - Page 181
FDC37B787-NS
Manufacturer Part Number
FDC37B787-NS
Description
Manufacturer
Standard Microsystems (SMSC)
Datasheet
1.FDC37B787-NS.pdf
(249 pages)
Specifications of FDC37B787-NS
Pin Count
128
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FDC37B787-NS
Manufacturer:
Standard
Quantity:
36
Company:
Part Number:
FDC37B787-NS
Manufacturer:
Microsemi
Quantity:
421
Company:
Part Number:
FDC37B787-NS
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
FDC37B787-NS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
- Current page: 181 of 249
- Download datasheet (866Kb)
DMA Channel Select Configuration Register
Note: A DMA channel is activated by setting the DMA Channel Select register to [0x00-0x03] AND :
for the FDC logical device by setting DMAEN, bit D3 of the Digital Output Register.
for the PP logical device in ECP mode by setting dmaEn, bit D3 of the ecr.
for the UART 2 logical device, by setting the DMA Enable bit. Refer to the IRCC specification.
Note: DMAREQ pins must tri-state if not used/selected by any Logical Device. Refer to Note A.
Note A. Logical Device IRQ and DMA Operation
1)
2)
3)
4)
IRQ and DMA Enable and Disable: Any time the IRQ or DACK for a logical block is disabled by a
register bit in that logical block, the IRQ and/or DACK must be disabled. This is in addition to the
IRQ and DACK disabled by the Configuration Registers (active bit or address not valid).
FDC: For the following cases, the IRQ and DACK used by the FDC are disabled (high impedance).
Will not respond to the DREQ.
a) Digital Output Register (Base+2) bit D3 (DMAEN) set to "0".
b) The FDC is in power down (disabled).
Serial Port 1 and 2: Modem Control Register (MCR) Bit D2 (OUT2) - When OUT2 is a logic "0", the
serial port interrupt is forced to a high impedance state - disabled.
Parallel Port: SPP and EPP modes: Control Port (Base+2) bit D4 (IRQE) set to "0", IRQ is disabled
(high impedance).
DMA Channel
Select
Default = 0x04
on Vcc POR or
Reset_Drv
TABLE 75 - DMA CHANNEL SELECT CONFIGURATION REGISTER DESCRIPTION
NAME
REG INDEX
0x74 (R/W)
Bits[2:0] select the DMA Channel.
0x00=DMA0
0x01=DMA1
0x02=DMA2
0x03=DMA3
0x04-0x07= No DMA active
184
DEFINITION
STATE
C
Related parts for FDC37B787-NS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
USB CHIP
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
ULTRA FAST USB 2.0 MULTI-SLOT FLASH MEDI
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet: