MT47H32M16HR-25E:F Micron Technology Inc, MT47H32M16HR-25E:F Datasheet - Page 79
![](/photos/31/34/313419/mfg557-84-fbga_sml.jpg)
MT47H32M16HR-25E:F
Manufacturer Part Number
MT47H32M16HR-25E:F
Description
Manufacturer
Micron Technology Inc
Type
DDR2 SDRAMr
Datasheet
1.MT47H32M16HR-25EF.pdf
(132 pages)
Specifications of MT47H32M16HR-25E:F
Organization
32Mx16
Density
512Mb
Address Bus
15b
Access Time (max)
400ps
Maximum Clock Rate
800MHz
Operating Supply Voltage (typ)
1.8V
Package Type
FBGA
Operating Temp Range
0C to 85C
Operating Supply Voltage (max)
1.9V
Operating Supply Voltage (min)
1.7V
Supply Current
295mA
Pin Count
84
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT47H32M16HR-25E:F
Manufacturer:
ON
Quantity:
700
Part Number:
MT47H32M16HR-25E:F
Manufacturer:
MICRON
Quantity:
20 000
CAS Latency (CL)
Figure 35: CL
PDF: 09005aef82f1e6e2
512MbDDR2.pdf - Rev. R 12/10 EN
Notes:
The CAS latency (CL) is defined by bits M4–M6, as shown in Figure 34 (page 76). CL is
the delay, in clock cycles, between the registration of a READ command and the availa-
bility of the first bit of output data. The CL can be set to 3, 4, 5, 6, or 7 clocks, depending
on the speed grade option being used.
DDR2 SDRAM does not support any half-clock latencies. Reserved states should not be
used as an unknown operation otherwise incompatibility with future versions may result.
DDR2 SDRAM also supports a feature called posted CAS additive latency (AL). This fea-
ture allows the READ command to be issued prior to
internal command to the DDR2 SDRAM by AL clocks. The AL feature is described in
further detail in Posted CAS Additive Latency (AL) (page 82).
Examples of CL = 3 and CL = 4 are shown in Figure 35; both assume AL = 0. If a READ
command is registered at clock edge n, and the CL is m clocks, the data will be available
nominally coincident with clock edge n + m (this assumes AL = 0).
DQS, DQS#
DQS, DQS#
Command
Command
1. BL = 4.
2. Posted CAS# additive latency (AL) = 0.
3. Shown with nominal
CK#
CK#
DQ
DQ
CK
CK
READ
READ
T0
T0
NOP
NOP
T1
T1
CL = 3 (AL = 0)
t
AC,
79
t
DQSCK, and
CL = 4 (AL = 0)
NOP
NOP
T2
T2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
t
DQSQ.
512Mb: x4, x8, x16 DDR2 SDRAM
NOP
NOP
T3
T3
DO
n
t
RCD (MIN) by delaying the
n + 1
DO
NOP
NOP
T4
T4
Mode Register (MR)
n + 2
DO
DO
n
© 2004 Micron Technology, Inc. All rights reserved.
Transitioning data
n + 1
n + 3
DO
DO
NOP
NOP
T5
T5
n + 2
DO
n + 3
DO
NOP
NOP
Don’t care
T6
T6