MT48LC2M32B2P-6:G Micron Technology Inc, MT48LC2M32B2P-6:G Datasheet - Page 20
![IC, SDRAM, 64MBIT, 166MHZ, TSOP-86](/photos/19/4/190475/4467798_sml.jpg)
MT48LC2M32B2P-6:G
Manufacturer Part Number
MT48LC2M32B2P-6:G
Description
IC, SDRAM, 64MBIT, 166MHZ, TSOP-86
Manufacturer
Micron Technology Inc
Type
SDRAMr
Series
-r
Specifications of MT48LC2M32B2P-6:G
Organization
2Mx32
Density
64Mb
Address Bus
13b
Access Time (max)
17/7.5/5.5ns
Maximum Clock Rate
166MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
180mA
Pin Count
86
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Memory Type
DRAM - Sychronous
Access Time
5.5ns
Page Size
64Mbit
Memory Case Style
TSOP
No. Of Pins
86
Operating Temperature Range
0°C To +70°C
Frequency
166MHz
Supply Voltage
3.3V
Format - Memory
RAM
Memory Size
64M (2Mx32)
Speed
167MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
86-TFSOP (0.400", 10.16mm Width)
Filter Terminals
SMD
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Compliant
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MT48LC2M32B2P-6:G
Manufacturer:
MICRON
Quantity:
20 000
Operation
Bank/Row Activation
Figure 8:
PDF: 09005aef80725c0b/Source: 09005aef806fc13c
64MSDRAM_2.fm - Rev. M 10/07 EN
Activating a Specific Row in a Specific Bank
Upon exiting the self refresh mode, AUTO REFRESH commands must be issued every
15.625µs or less, as both SELF REFRESH and AUTO REFRESH utilize the row refresh
counter.
Before any READ or WRITE commands can be issued to a bank within the SDRAM, a row
in that bank must be “opened.” This is accomplished via the ACTIVE command, which
selects both the bank and the row to be activated (see Figure 8).
After opening a row (issuing an ACTIVE command), a READ or WRITE command may be
issued to that row, subject to the
the clock period and rounded up to the next whole number to determine the earliest
clock edge after the ACTIVE command on which a READ or WRITE command can be
entered. For example, a
results in 2.5 clocks, rounded to 3. This is reflected in Figure 9 on page 21, which covers
any case where 2 <
specification limits from time units to clock cycles).
A subsequent ACTIVE command to a different row in the same bank can only be issued
after the previous active row has been “closed” (precharged). The minimum time
interval between successive ACTIVE commands to the same bank is defined by
A subsequent ACTIVE command to another bank can be issued while the first bank is
being accessed, which results in a reduction of total row-access overhead. The
minimum time interval between successive ACTIVE commands to different banks is
defined by
A0–A10, A11
BA0, BA1
RAS#
CAS#
WE#
CKE
CLK
CS#
t
RRD.
HIGH
t
RCD (MIN)/
t
RCD specification of 20ns with a 125 MHz clock (8ns period)
ADDRESS
ADDRESS
BANK
ROW
20
t
t
CK ≤ 3. (The same procedure is used to convert other
DON’T CARE
RCD specification.
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
RCD (MIN) should be divided by
64Mb: x4, x8, x16 SDRAM
©2000 Micron Technology, Inc. All rights reserved.
Commands
t
RC.