DS33R11 Maxim Integrated Products, DS33R11 Datasheet - Page 242

• Manufacturer Part Number: DS33R11
• Description: Network Controller & Processor ICs Ethernet Mapper with Integrated T1-E1-J1
• Manufacturer: Maxim Integrated Products

Specifications of DS33R11

• Product: Framer
• Number Of Transceivers: 1
• Supply Voltage (max): 1.89 V, 3.465 V
• Supply Voltage (min): 1.71 V, 3.135 V
• Supply Current (max): 100 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Package / Case: BGA

Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 4: Line Interface Unit Mux Control (LIUC). This is a software version of the LIUC pin. When the LIUC pin is
connected high, the LIUC bit has control. When the LIUC pin is connected low, the framer and LIU are separated
and the LIUC bit has no effect.
Bit 3: Local Loopback (LLB). When this bit is set to 1, data continues to be transmitted as normal through the
transmit side of the transceiver. Data being received at RTIP and RRING are replaced with the data being
transmitted. Data in this loopback passes through the jitter attenuator. See
Bit 2: Remote Loopback (RLB). When this bit is set to 1, data input by the RPOSI and RNEGI pins is transmitted
back to the TPOSO and TNEGO pins. Data continues to pass through the receive-side framer of the transceiver as
it would normally. Data from the transmit-side formatter is ignored. See
Bit 1: Payload Loopback (PLB). When set to 1, payload loopback is enabled and the following occurs:
1) Data is transmitted from the TPOSO and TNEGO pins synchronous with RCLKO instead of TCLKT.
2) All the receive side signals continue to operate normally.
3) Data at the TSERI, TDATA, and TSIG pins is ignored.
T1 Mode: Normally, this loopback is only enabled when ESF framing is being performed but can also be enabled in
D4 framing applications. The transceiver loops the 192 bits of payload data (with BPVs corrected) from the receive
section back to the transmit section. The FPS framing pattern, CRC6 calculation, and the FDL bits are not looped
back; they are reinserted by the transceiver.
E1 Mode: The transceiver loops the 248 bits of payload data (with BPVs corrected) from the receive section back
to the transmit section. The transmit section modifies the payload as if it was input at TSERI. The FAS word; Si,
Sa, and E bits; and CRC4 are not looped back; they are reinserted by the transceiver.
Bit 0: Framer Loopback (FLB). When this bit is set to 1, the transceiver loops data from the transmit side back to
the receive side. When FLB is enabled, the following occurs:
1) T1 Mode: An unframed all-ones code is transmitted at TPOSO and TNEGO.
2) Data at RPOSI and RNEGI is ignored.
3) All receive-side signals take on timing synchronous with TCLKT instead of RDCLKI.
Please note that it is not acceptable to have RCLKO connected to TCLKT during this loopback because this
causes an unstable condition.
LIUC Pin
E1 Mode: Normal data is transmitted at TPOSO and TNEGO.
0
0
1
1
0 = LIU internally connected to framer.
1 = LIU disconnected from framer. Use TPOSI/TNEGI/TDCLKI/RPOSI/RNEGI/RDCLKI pins
—
7
0
LIUC Bit
0
1
0
1
TR.LBCR
Loopback Control Register
4Ah
—
6
0
LIU and framer separated
LIU and framer separated
LIU and framer connected
LIU and framer separated
Condition
—
5
0
242 of 344
LIUC
0
4
LLB
3
0
Figure 6-2
Figure 6-3
RLB
2
0
for more details.
for more details.
PLB
1
0
FLB
0
0