HSC-ADC-FIFO5-INTZ Analog Devices Inc, HSC-ADC-FIFO5-INTZ Datasheet - Page 4

• Manufacturer Part Number: HSC-ADC-FIFO5-INTZ
• Description: Interposer Quad/octal ADCs
• Manufacturer: Analog Devices Inc

Specifications of HSC-ADC-FIFO5-INTZ

• Accessory Type: ADC Interface Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: AD6640
• Lead Free Status / Rohs Status: Supplier Unconfirmed

HSC-ADC-EVALA-SC/HSC-ADC-EVALA-DC
FIFO EVALUATION BOARD QUICK START
Install ADC Analyzer from the CD provided in the FIFO
evaluation kit. See the Installing ADC Analyzer section for more
details. For the latest updates to the software, check the Analog
Devices website at www.analog.com/hsc-FIFO.
REQUIREMENTS
Requirements include
•
•
•
•
•
•
•
•
Quick Start Steps
1.
2.
3.
4.
FIFO evaluation board, ADC Analyzer, and USB cable
High speed ADC evaluation board and ADC data sheet
3.3 V power supply for FIFO evaluation board
Power supply for ADC evaluation board
Analog signal source and appropriate filtering
Low jitter clock source applicable for specific ADC
evaluation, typically < 1 ps rms
PC running Windows 98 (2nd Ed), Windows 2000,
Windows Me, or Windows XP
PC with a USB 2.0 port recommended (USB 1.1
compatible)
Connect the FIFO evaluation board to the ADC evaluation
board. If an adapter is required, insert the adapter between
the ADC evaluation board and the FIFO board. If using the
HSC-ADC-EVALA-SC model, connect the evaluation
board to the bottom half of the 80-pin connector (closest
to the installed IDT FIFO chip).
Connect the provided USB cable to the FIFO evaluation
board and to an available USB port on the computer.
Refer to Table 4 for any jumper changes. Most evaluation
boards can be used with the default settings.
After verification, connect the appropriate power supplies
to the FIFO and ADC evaluation boards. The FIFO
evaluation board requires a single 3.3 V power supply with
1 A current capability. Refer to the instructions included in
the ADC data sheet for more information about the ADC
evaluation board setup.
Rev. 0 | Page 4 of 44
5.
6.
7.
8.
9.
10. Choose a configuration file for the ADC evaluation board
11. Click Time Domain (left-most button under the pull-
Once the cable is connected to both the computer and
FIFO and power is supplied, the USB drivers start to install.
To complete the total installation of the FIFO drivers, you
need to complete the new hardware sequence two times.
The first Found New Hardware Wizard opens with the text
message This wizard helps you install software for…Pre-
FIFO 4. Click the recommended install, and go to the next
screen. A Hardware Installation warning window should
then be displayed. Click Continue Anyway. The next
window that opens should finish the Pre-FIFO 4
installation. Click Finish to complete. Your computer
should go through a second Found New Hardware Wizard,
and the text message, This wizard helps you install
software for…Analog Devices FIFO 4, should be
displayed Continue as you did in the previous installation
and click Continue Anyway, then click Finish on the next
two windows. This should complete the installation.
(Optional) Verify in the device manager that “Analog
Devices, FIFO4” is listed under the USB hardware.
Apply power to the evaluation board and check the voltage
levels at the board level.
Connect the appropriate analog input (which should be
filtered with a band-pass filter) and low jitter clock signal.
Make sure the evaluation boards are powered before
connecting the analog input and clock.
Start ADC Analyzer (see the Installation section for
installing the software).
used or create one (see the Configuring an Evaluation
Board section for more information).
down menus). A reconstruction of the analog input is
displayed. If the expected signal does not appear, or if there
is only a flat red line, refer to the Troubleshooting section
for more information.