ADV7183BBSTZ Analog Devices Inc, ADV7183BBSTZ Datasheet - Page 38

• Manufacturer Part Number: ADV7183BBSTZ
• Description: IC,TV/VIDEO CIRCUIT,Color Decoder Circuit,CMOS,QFP,80PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Video Decoderr

Specifications of ADV7183BBSTZ

• Applications: Projectors, Recorders, Security
• Voltage - Supply, Analog: 3.15 V ~ 3.45 V
• Voltage - Supply, Digital: 1.65 V ~ 2 V
• Mounting Type: Surface Mount
• Package / Case: 80-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADV7183B
BL_C_VBI Blank Chroma During VBI, Address 0x04[2]
Setting BL_C_VBI high, the Cr and Cb values of all VBI lines
are blanked. This is done so any data that arrives during VBI is
not decoded as color and output through Cr and Cb. As a result,
it should be possible to send VBI lines into the decoder, then
output them through an encoder again, undistorted. Without
this blanking, any wrongly decoded color is encoded by the
video encoder; therefore, the VBI lines are distorted.
Setting BL_C_VBI to 0 decodes and outputs color during VBI.
Setting BL_C_VBI to 1 (default) blanks Cr and Cb values
during VBI.
RANGE Range Selection, Address 0x04[0]
AV codes (as per ITU-R BT-656, formerly known as CCIR-656)
consist of a fixed header made up of 0xFF and 0x00 values.
These two values are reserved and therefore cannot be used for
active video. Additionally, the ITU specifies that the nominal
range for video should be restricted to values between 16 and
235 for luma and 16 to 240 for chroma.
The RANGE bit allows the user to limit the range of values
output by the ADV7183B to the recommended value range. In
any case, it ensures that the reserved values of 255d (0xFF) and
00d (0x00) are not presented on the output pins unless they are
part of an AV code header.
Table 52. RANGE Function
RANGE
0
1 (default)
AUTO_PDC_EN Automatic Programmed Delay Control,
Address 0x27[6]
Enabling the AUTO_PDC_EN function activates a function
within the ADV7183B that automatically programs the
LTA[1:0] and CTA[2:0] to have the chroma and luma data
match delays for all modes of operation. If set, manual registers
LTA[1:0] and CTA[2:0] are not used. If the automatic mode
is disabled (via setting the AUTO_PDC_EN bit to 0), the
values programmed into LTA[1:0] and CTA[2:0] registers
become active.
When AUTO_PDC_EN is 0, the ADV7183 uses the LTA[1:0]
and CTA[2:0] values for delaying luma and chroma samples.
Refer to the
and the
sections.
When AUTO_PDC_EN is 1 (default), the ADV7183B auto-
matically determines the LTA and CTA values to have luma
and chroma aligned at the output.
C TA[2:0] Chroma Timing Adjust, Address 0x27[5:3]
2 0 4 H
L TA[1:0] Luma Timing Adjust, Address 0x27[1:0]
2 0 3 H
Description
16 ≤ Y ≤ 235
1 ≤ Y ≤ 254
16 ≤ C/P ≤ 240
1 ≤ C/P ≤ 254
Rev. B | Page 38 of 100
LTA[1:0] Luma Timing Adjust, Address 0x27[1:0]
The Luma Timing Adjust register allows the user to specify a
timing difference between chroma and luma samples.
There is a certain functionality overlap with the CTA[2:0]
register. For manual programming, use the following defaults:
•
•
•
Table 53. LTA Function
LTA[1:0]
00 (default)
01
10
11
CTA[2:0] Chroma Timing Adjust, Address 0x27[5:3]
The Chroma Timing Adjust register allows the user to specify a
timing difference between chroma and luma samples. This can
be used to compensate for external filter group delay differences
in the luma vs. chroma path, and to allow a different number of
pipeline delays while processing the video downstream. Review
this functionality together with the LTA[1:0] register.
The chroma can only be delayed/advanced in chroma pixel
steps. One chroma pixel step is equal to two luma pixels. The
programmable delay occurs after demodulation, where one
can no longer delay by luma pixel steps.
For manual programming, use the following defaults:
•
•
•
Table 54. CTA Function
CTA[2:0]
000
001
010
011 (default)
100
101
110
111
CVBS input LTA[1:0] = 00
Y/C input LTA[1:0] = 01
YPrPb input LTA[1:0] = 01
CVBS input CTA[2:0] = 011
Y/C input CTA[2:0] = 101
YPrPb input CTA[2:0] =110
Description
No delay
Luma 1 clk (37 ns) delayed
Luma 2 clk (74 ns) early
Luma 1 clk (37 ns) early
Description
Not used
Chroma + 2 chroma pixel (early)
Chroma + 1 chroma pixel (early)
No delay
Chroma – 1 chroma pixel (late)
Chroma – 2 chroma pixel (late)
Chroma – 3 chroma pixel (late)
Not used